Poulan PDC18H42STA To Adjust Gauge Wheels See Fig, To Operate on Hills, To Operate Mower See Fig

Page 12
Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

OPERATION

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

Remove retainer spring and clevis pin which secure each gauge wheel bar.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

Replace retainer spring into clevis pin.

Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS

PIN

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

Select desired height of cut.

Lower mower with attachment lift control.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

12

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

Choose the slowest speed before starting up or down hills.

Avoid stopping or changing speed on hills.

If slowing is necessary, move throttle control lever to slower position.

If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/ BRAKE PEDAL IS DEPRESSED.

To restart movement, slowly release parking brake and clutch/brake pedal.

Slowly move motion control lever to slowest setting.

Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

Raise attachment lift to highest position with attachment lift control.

Pull freewheel control out and into the slot and release so it is held in the disengaged position.

Do not push or tow tractor at more than two (2) MPH.

To reengage transmission, reverse above procedure.

Image 12
Contents PDC18H42STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips Maintenance Lubrication ChartService Dates General RecommendationsTractor Engine Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control Cable See FigTo Adjust Carburetor Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PDC18H42STA, Product no 57Tractor - Model Number PDC18H42STA, Product no 57 Electrical KEY Part NO. NO. Description 209 208 207 142 212 161 145 KEY Part Description Tractor - Model Number PDC18H42STA, Product no 57 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PDC18H42STA, Product no 57 Engine KEY Part NO. NO. Description KEY Part Description Tractor - Model Number PDC18H42STA, Product no 57 Decals Wheels & TiresTractor - Model Number PDC18H42STA, Product no 57 Mower Lift Repair Parts Tractor - Model Number PDC18H42STA, Product no 57 Mower Deck 182032X421 Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PDC18H42STA specifications

The Poulan PDC18H42STA is a robust riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. Packed with innovative features and advanced technologies, this machine is engineered to make mowing larger lawns a simpler and more enjoyable task.

One of the standout features of the Poulan PDC18H42STA is its powerful 18 HP engine. This reliable engine provides the necessary power to tackle tough grass conditions and uneven terrains, ensuring that the mower operates smoothly without bogging down. The mower's speed is adjustable, allowing users to choose the ideal pace for their specific lawn care needs.

The 42-inch cutting deck is another impressive characteristic of this model. This wide cutting deck enables the Poulan mower to cover large areas efficiently, reducing the overall mowing time. With a three-blade system, the mower offers a clean and even cut, resulting in a beautifully manicured lawn. Additionally, the cutting height is easily adjustable, ranging from one to four inches, allowing for tailored cutting heights based on seasonal conditions and grass types.

A notable technology implemented in the Poulan PDC18H42STA is its ergonomic design, which includes a comfortable high-back seat and a user-friendly control panel. The controls are intuitively positioned, enabling operators to adjust speed, cutting height, and direction with ease. The steering system features a tight turning radius, which is essential for maneuvering around obstacles and making precise turns on the lawn.

Durability is paramount in the construction of the Poulan PDC18H42STA. The mower features a steel frame and a reinforced cutting deck, ensuring longevity and resilience against wear and tear. Furthermore, with its maintenance-free battery and efficient fuel consumption, this mower is designed for prolonged use with minimal upkeep.

Safety is also a critical consideration in the design of the Poulan PDC18H42STA. The mower is equipped with safety features such as an automatic blade brake that engages when the operator leaves the seat, preventing accidents and promoting a safer mowing experience.

In summary, the Poulan PDC18H42STA stands out in the realm of riding lawn mowers with its powerful engine, wide cutting deck, user-friendly design, and durable construction. It combines advanced technologies and features that make lawn care more efficient, giving homeowners a reliable tool for maintaining their outdoor spaces.