Poulan PDC18H42STA Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEY

CENTER SPAN KEEPER

FIG. 25

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PDC18H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Gauge WheelTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See a Check Battery See FigCheck Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips General Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentInterlocks and Relays To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PDC18H42STA, Product no 57 SchematicTractor - Model Number PDC18H42STA, Product no 57 Electrical KEY Part NO. NO. Description 209 208 207 142 212 161 145 KEY Part Description Tractor - Model Number PDC18H42STA, Product no 57 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PDC18H42STA, Product no 57 Engine KEY Part NO. NO. Description KEY Part Description Wheels & Tires Tractor - Model Number PDC18H42STA, Product no 57 DecalsTractor - Model Number PDC18H42STA, Product no 57 Mower Lift Repair Parts Tractor - Model Number PDC18H42STA, Product no 57 Mower Deck 182032X421 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDC18H42STA specifications

The Poulan PDC18H42STA is a robust riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. Packed with innovative features and advanced technologies, this machine is engineered to make mowing larger lawns a simpler and more enjoyable task.

One of the standout features of the Poulan PDC18H42STA is its powerful 18 HP engine. This reliable engine provides the necessary power to tackle tough grass conditions and uneven terrains, ensuring that the mower operates smoothly without bogging down. The mower's speed is adjustable, allowing users to choose the ideal pace for their specific lawn care needs.

The 42-inch cutting deck is another impressive characteristic of this model. This wide cutting deck enables the Poulan mower to cover large areas efficiently, reducing the overall mowing time. With a three-blade system, the mower offers a clean and even cut, resulting in a beautifully manicured lawn. Additionally, the cutting height is easily adjustable, ranging from one to four inches, allowing for tailored cutting heights based on seasonal conditions and grass types.

A notable technology implemented in the Poulan PDC18H42STA is its ergonomic design, which includes a comfortable high-back seat and a user-friendly control panel. The controls are intuitively positioned, enabling operators to adjust speed, cutting height, and direction with ease. The steering system features a tight turning radius, which is essential for maneuvering around obstacles and making precise turns on the lawn.

Durability is paramount in the construction of the Poulan PDC18H42STA. The mower features a steel frame and a reinforced cutting deck, ensuring longevity and resilience against wear and tear. Furthermore, with its maintenance-free battery and efficient fuel consumption, this mower is designed for prolonged use with minimal upkeep.

Safety is also a critical consideration in the design of the Poulan PDC18H42STA. The mower is equipped with safety features such as an automatic blade brake that engages when the operator leaves the seat, preventing accidents and promoting a safer mowing experience.

In summary, the Poulan PDC18H42STA stands out in the realm of riding lawn mowers with its powerful engine, wide cutting deck, user-friendly design, and durable construction. It combines advanced technologies and features that make lawn care more efficient, giving homeowners a reliable tool for maintaining their outdoor spaces.
Top Page Image Contents