Poulan PDC18H42STA owner manual Check Battery See Fig, Assemble Gauge Wheels to Mower Deck See a

Page 7

ASSEMBLY

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4A)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor-

mance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

 

RETAINER SPRING

 

PIN

 

ADJUSTING

 

BAR

SHOULDER

 

BOLT

 

GAUGE

3/8-16 CENTER

WHEEL

LOCKNUT

 

3/8 WASHER

7

FIG. 4A

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PDC18H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Gauge WheelTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See a Check Battery See FigCheck Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips General Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentInterlocks and Relays To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Adjust Throttle Control Cable See Fig To Remove Hood and Grill Assembly See FigTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PDC18H42STA, Product no 57 SchematicTractor - Model Number PDC18H42STA, Product no 57 Electrical KEY Part NO. NO. Description 209 208 207 142 212 161 145 KEY Part Description Tractor - Model Number PDC18H42STA, Product no 57 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PDC18H42STA, Product no 57 Engine KEY Part NO. NO. Description KEY Part Description Wheels & Tires Tractor - Model Number PDC18H42STA, Product no 57 DecalsTractor - Model Number PDC18H42STA, Product no 57 Mower Lift Repair Parts Tractor - Model Number PDC18H42STA, Product no 57 Mower Deck 182032X421 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDC18H42STA specifications

The Poulan PDC18H42STA is a robust riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. Packed with innovative features and advanced technologies, this machine is engineered to make mowing larger lawns a simpler and more enjoyable task.

One of the standout features of the Poulan PDC18H42STA is its powerful 18 HP engine. This reliable engine provides the necessary power to tackle tough grass conditions and uneven terrains, ensuring that the mower operates smoothly without bogging down. The mower's speed is adjustable, allowing users to choose the ideal pace for their specific lawn care needs.

The 42-inch cutting deck is another impressive characteristic of this model. This wide cutting deck enables the Poulan mower to cover large areas efficiently, reducing the overall mowing time. With a three-blade system, the mower offers a clean and even cut, resulting in a beautifully manicured lawn. Additionally, the cutting height is easily adjustable, ranging from one to four inches, allowing for tailored cutting heights based on seasonal conditions and grass types.

A notable technology implemented in the Poulan PDC18H42STA is its ergonomic design, which includes a comfortable high-back seat and a user-friendly control panel. The controls are intuitively positioned, enabling operators to adjust speed, cutting height, and direction with ease. The steering system features a tight turning radius, which is essential for maneuvering around obstacles and making precise turns on the lawn.

Durability is paramount in the construction of the Poulan PDC18H42STA. The mower features a steel frame and a reinforced cutting deck, ensuring longevity and resilience against wear and tear. Furthermore, with its maintenance-free battery and efficient fuel consumption, this mower is designed for prolonged use with minimal upkeep.

Safety is also a critical consideration in the design of the Poulan PDC18H42STA. The mower is equipped with safety features such as an automatic blade brake that engages when the operator leaves the seat, preventing accidents and promoting a safer mowing experience.

In summary, the Poulan PDC18H42STA stands out in the realm of riding lawn mowers with its powerful engine, wide cutting deck, user-friendly design, and durable construction. It combines advanced technologies and features that make lawn care more efficient, giving homeowners a reliable tool for maintaining their outdoor spaces.
Top Page Image Contents