Poulan PDC18H42STA owner manual Cleaning, Clean AIR INTAKE/COOLING Areas, Muffler, Spark Plugs

Page 19

MAINTENANCE

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

AIR FILTER (See Fig. 16)

Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first.

Service air cleaner more often under dusty conditions.

•Remove knob and cover.

•Remove wing nut and air cleaner from base.

TO SERVICE PRE-CLEANER

•Slide foam pre-cleaner off cartridge.

•Wash it in liquid detergent and water.

•Squeeze it dry in a clean cloth. Allow it to dry.

•Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to remove excess oil.

TO SERVICE CARTRIDGE

•Replace a dirty, bent, or damaged cartridge.

NOTE: Do not wash the paper cartridge or use pressurized air, as this will damage the cartridge.

•Reinstall the pre-cleaner (cleaned and oiled) over the paper cartridge.

•Reassemble air cleaner, wing nut, cover and tighten knob securely.

COVER KNOB

AIR CLEANER

COVER

WING NUT

FOAM PRE-CLEANER

RUBBER

GROMMET

AIR CLEANER

AIR CLEANER

BASE

PAPER CARTRIDGE

 

OIL FILL CAP/

DIPSTICK

AIR

SCREEN

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 17)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

 

FUEL

FILTER

FIG. 17

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

FIG. 16

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents PDC18H42STA Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Gauge WheelTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See a Check Battery See FigCheck Deck Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Operate Mower See FigADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips General Recommendations MaintenanceLubrication Chart Service DatesTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel ALIGN- MentInterlocks and Relays To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Adjust Throttle Control Cable See Fig To Remove Hood and Grill Assembly See FigTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PDC18H42STA, Product no 57 SchematicTractor - Model Number PDC18H42STA, Product no 57 Electrical KEY Part NO. NO. Description 209 208 207 142 212 161 145 KEY Part Description Tractor - Model Number PDC18H42STA, Product no 57 Drive Repair Parts Repair Parts 180656 Wheel Steering Tractor - Model Number PDC18H42STA, Product no 57 Engine KEY Part NO. NO. Description KEY Part Description Wheels & Tires Tractor - Model Number PDC18H42STA, Product no 57 DecalsTractor - Model Number PDC18H42STA, Product no 57 Mower Lift Repair Parts Tractor - Model Number PDC18H42STA, Product no 57 Mower Deck 182032X421 Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PDC18H42STA specifications

The Poulan PDC18H42STA is a robust riding lawn mower designed for homeowners seeking efficiency and reliability in lawn care. Packed with innovative features and advanced technologies, this machine is engineered to make mowing larger lawns a simpler and more enjoyable task.

One of the standout features of the Poulan PDC18H42STA is its powerful 18 HP engine. This reliable engine provides the necessary power to tackle tough grass conditions and uneven terrains, ensuring that the mower operates smoothly without bogging down. The mower's speed is adjustable, allowing users to choose the ideal pace for their specific lawn care needs.

The 42-inch cutting deck is another impressive characteristic of this model. This wide cutting deck enables the Poulan mower to cover large areas efficiently, reducing the overall mowing time. With a three-blade system, the mower offers a clean and even cut, resulting in a beautifully manicured lawn. Additionally, the cutting height is easily adjustable, ranging from one to four inches, allowing for tailored cutting heights based on seasonal conditions and grass types.

A notable technology implemented in the Poulan PDC18H42STA is its ergonomic design, which includes a comfortable high-back seat and a user-friendly control panel. The controls are intuitively positioned, enabling operators to adjust speed, cutting height, and direction with ease. The steering system features a tight turning radius, which is essential for maneuvering around obstacles and making precise turns on the lawn.

Durability is paramount in the construction of the Poulan PDC18H42STA. The mower features a steel frame and a reinforced cutting deck, ensuring longevity and resilience against wear and tear. Furthermore, with its maintenance-free battery and efficient fuel consumption, this mower is designed for prolonged use with minimal upkeep.

Safety is also a critical consideration in the design of the Poulan PDC18H42STA. The mower is equipped with safety features such as an automatic blade brake that engages when the operator leaves the seat, preventing accidents and promoting a safer mowing experience.

In summary, the Poulan PDC18H42STA stands out in the realm of riding lawn mowers with its powerful engine, wide cutting deck, user-friendly design, and durable construction. It combines advanced technologies and features that make lawn care more efficient, giving homeowners a reliable tool for maintaining their outdoor spaces.
Top Page Image Contents