Poulan PD2042STA owner manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 13

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

•The attachments can be used during the engine warm- up period and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PD2042STA Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsGauge Wheel BladeTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONAssemble Gauge Wheels to Mower Deck See a Check Battery See FigTo Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsService Dates MaintenanceGeneral Recommendations Before Each USETractor Engine To Clean Battery and TerminalsBelts Transaxle CoolingCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Remove Hood and Grill Assembly See FigTo Adjust Choke Control See Fig To Adjust CarburetorOther StorageFuel System Engine OILTroubleshooting Points OFF Page Tractor - Model Number PD2042STA, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Wheels and Tires DecalsOptional Equipment EngineMower Lift Mower Deck CAB Page Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PD2042STA specifications

The Poulan PD2042STA is a robust and efficient riding lawn mower designed to meet the needs of homeowners with medium to large lawns. With a perfect blend of power, performance, and user-friendly features, this riding mower stands out in its category.

One of the key features of the Poulan PD2042STA is its powerful 42-inch cutting deck. This size allows for wide paths of grass to be trimmed in fewer passes, making lawn care quicker and more efficient. The mower is equipped with a reliable 19.5 horsepower Briggs & Stratton engine that provides ample power for cutting dense grass and maneuvering through varying terrains.

Ease of use is a hallmark of the PD2042STA, with its foot-pedal-operated automatic transmission. This technology allows for smooth acceleration and deceleration without the need for manual gear shifting. Mowing your lawn becomes a breeze, as the mower adapts effortlessly to the operator's speed preferences.

Additionally, the PD2042STA features a customizable cutting height ranging from 1 to 4 inches. This versatility ensures that users can achieve the desired lawn finish for different grass types and seasonal conditions. The mower also incorporates a durable steel deck that not only withstands the rigors of mowing but also promotes superior grass clipping discharge, ensuring a clean finish.

For comfort during use, the PD2042STA includes an ergonomically designed, high-back seat that provides support during extended mowing sessions. The soft-touch steering wheel enhances maneuverability, allowing for easy control around obstacles like flower beds and trees.

Maintenance is made simple with the inclusion of an easy-access battery and engine compartment, as well as a deck wash port that enables quick cleaning of the cutting deck after use. These features encourage regular upkeep, which extends the life of the mower and ensures optimal performance.

The Poulan PD2042STA also showcases a rugged design and sturdy construction, designed to handle rough terrains and provide longevity. With features like a large fuel tank and a front-mounted bumper, this riding mower is built for both efficiency and durability.

In summary, the Poulan PD2042STA is an excellent choice for homeowners seeking a dependable riding mower that combines power, comfort, and technological advancements. Its robust engine, user-friendly features, and high-quality construction make it a worthy investment for maintaining a beautiful lawn.
Top Page Image Contents