Poulan PD2042STA owner manual Cleaning

Page 18

MAINTENANCE

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

AIR FILTER (See Fig. 15)

Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first.

Service air cleaner more often under dusty conditions.

•Remove knobs and cover.

TO SERVICE PRE-CLEANER

•Wash it in liquid detergent and water.

•Squeeze it dry in a clean cloth.

•Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to remove excess oil.

•If very dirty or damaged, replace pre-cleaner.

TO SERVICE CARTRIDGE

•Clean cartridge by tapping gently on flat surface. If very dirty or damaged, replace cartridge.

•Reinstall precleaner cartridge, cover and secure with knobs.

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KEROSENE, ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. THEY MAY CAUSE DETERIORATION OF THE CARTRIDGE. DO NOT OIL CARTRIDGE. DO NOT USE PRESSURIZED AIRTO CLEAN OR DRY CARTRIDGE.

KNOBS

COVER

CARTRIDGE

FOAM

PRE-CLEANER

FIG. 15

ENGINE OIL FILTER

Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 16)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

 

FUEL

FILTER

FIG. 16

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PD2042STA Safety Rules Safety Rules Table of Contents Gauge Wheel Unassembled PartsSteering Wheel Seat BladeHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aCheck Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsGeneral Recommendations MaintenanceService Dates Before Each USETractor Belts To Clean Battery and TerminalsEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs Interlocks and RelaysTo Adjust Choke Control See Fig To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points OFF Page Schematic Tractor - Model Number PD2042STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck CAB Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD2042STA specifications

The Poulan PD2042STA is a robust and efficient riding lawn mower designed to meet the needs of homeowners with medium to large lawns. With a perfect blend of power, performance, and user-friendly features, this riding mower stands out in its category.

One of the key features of the Poulan PD2042STA is its powerful 42-inch cutting deck. This size allows for wide paths of grass to be trimmed in fewer passes, making lawn care quicker and more efficient. The mower is equipped with a reliable 19.5 horsepower Briggs & Stratton engine that provides ample power for cutting dense grass and maneuvering through varying terrains.

Ease of use is a hallmark of the PD2042STA, with its foot-pedal-operated automatic transmission. This technology allows for smooth acceleration and deceleration without the need for manual gear shifting. Mowing your lawn becomes a breeze, as the mower adapts effortlessly to the operator's speed preferences.

Additionally, the PD2042STA features a customizable cutting height ranging from 1 to 4 inches. This versatility ensures that users can achieve the desired lawn finish for different grass types and seasonal conditions. The mower also incorporates a durable steel deck that not only withstands the rigors of mowing but also promotes superior grass clipping discharge, ensuring a clean finish.

For comfort during use, the PD2042STA includes an ergonomically designed, high-back seat that provides support during extended mowing sessions. The soft-touch steering wheel enhances maneuverability, allowing for easy control around obstacles like flower beds and trees.

Maintenance is made simple with the inclusion of an easy-access battery and engine compartment, as well as a deck wash port that enables quick cleaning of the cutting deck after use. These features encourage regular upkeep, which extends the life of the mower and ensures optimal performance.

The Poulan PD2042STA also showcases a rugged design and sturdy construction, designed to handle rough terrains and provide longevity. With features like a large fuel tank and a front-mounted bumper, this riding mower is built for both efficiency and durability.

In summary, the Poulan PD2042STA is an excellent choice for homeowners seeking a dependable riding mower that combines power, comfort, and technological advancements. Its robust engine, user-friendly features, and high-quality construction make it a worthy investment for maintaining a beautiful lawn.
Top Page Image Contents