Poulan PD2042STA owner manual Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

Utility knife

Pliers

(1)

3/4" wrenches

Tire pressure gauge

(2)

7/16" wrenches

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•

Position front wheels of the tractor so they are pointing straight

 

forward.

•

Remove steering wheel adapter from steering wheel and

 

slide adapter onto steering shaft extension.

STEERING

WHEEL

ADAPTER

1/4 LOCKNUT

LOWER

STEERING

SHAFT

INSERT

1/2 HEX NUT

LARGE FLAT

WASHER

STEERING

BOOT

TABS

EXTENSION SHAFT

1/4 HEX BOLT

TAB

SLOTS

FIG. 1

• Position steering wheel so cross bars are horizontal (left to

right) and slide inside boot and onto adapter.

• Assemble large flat washer, 1/2 hex nut and tighten se-

curely.

• Snap steering wheel insert into center of steering wheel.

• Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PD2042STA Safety Rules Safety Rules Table of Contents Gauge Wheel Unassembled PartsSteering Wheel Seat BladeHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aCheck Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsGeneral Recommendations MaintenanceService Dates Before Each USETractor Belts To Clean Battery and TerminalsEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs Interlocks and RelaysTo Adjust Choke Control See Fig To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points OFF Page Schematic Tractor - Model Number PD2042STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck CAB Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD2042STA specifications

The Poulan PD2042STA is a robust and efficient riding lawn mower designed to meet the needs of homeowners with medium to large lawns. With a perfect blend of power, performance, and user-friendly features, this riding mower stands out in its category.

One of the key features of the Poulan PD2042STA is its powerful 42-inch cutting deck. This size allows for wide paths of grass to be trimmed in fewer passes, making lawn care quicker and more efficient. The mower is equipped with a reliable 19.5 horsepower Briggs & Stratton engine that provides ample power for cutting dense grass and maneuvering through varying terrains.

Ease of use is a hallmark of the PD2042STA, with its foot-pedal-operated automatic transmission. This technology allows for smooth acceleration and deceleration without the need for manual gear shifting. Mowing your lawn becomes a breeze, as the mower adapts effortlessly to the operator's speed preferences.

Additionally, the PD2042STA features a customizable cutting height ranging from 1 to 4 inches. This versatility ensures that users can achieve the desired lawn finish for different grass types and seasonal conditions. The mower also incorporates a durable steel deck that not only withstands the rigors of mowing but also promotes superior grass clipping discharge, ensuring a clean finish.

For comfort during use, the PD2042STA includes an ergonomically designed, high-back seat that provides support during extended mowing sessions. The soft-touch steering wheel enhances maneuverability, allowing for easy control around obstacles like flower beds and trees.

Maintenance is made simple with the inclusion of an easy-access battery and engine compartment, as well as a deck wash port that enables quick cleaning of the cutting deck after use. These features encourage regular upkeep, which extends the life of the mower and ensures optimal performance.

The Poulan PD2042STA also showcases a rugged design and sturdy construction, designed to handle rough terrains and provide longevity. With features like a large fuel tank and a front-mounted bumper, this riding mower is built for both efficiency and durability.

In summary, the Poulan PD2042STA is an excellent choice for homeowners seeking a dependable riding mower that combines power, comfort, and technological advancements. Its robust engine, user-friendly features, and high-quality construction make it a worthy investment for maintaining a beautiful lawn.
Top Page Image Contents