Poulan PD2042STA To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS PIN

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PD2042STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel BladeAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsMaintenance Service DatesGeneral Recommendations Before Each USETractor To Clean Battery and Terminals EngineBelts Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points OFF Page Schematic Tractor - Model Number PD2042STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck CAB Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD2042STA specifications

The Poulan PD2042STA is a robust and efficient riding lawn mower designed to meet the needs of homeowners with medium to large lawns. With a perfect blend of power, performance, and user-friendly features, this riding mower stands out in its category.

One of the key features of the Poulan PD2042STA is its powerful 42-inch cutting deck. This size allows for wide paths of grass to be trimmed in fewer passes, making lawn care quicker and more efficient. The mower is equipped with a reliable 19.5 horsepower Briggs & Stratton engine that provides ample power for cutting dense grass and maneuvering through varying terrains.

Ease of use is a hallmark of the PD2042STA, with its foot-pedal-operated automatic transmission. This technology allows for smooth acceleration and deceleration without the need for manual gear shifting. Mowing your lawn becomes a breeze, as the mower adapts effortlessly to the operator's speed preferences.

Additionally, the PD2042STA features a customizable cutting height ranging from 1 to 4 inches. This versatility ensures that users can achieve the desired lawn finish for different grass types and seasonal conditions. The mower also incorporates a durable steel deck that not only withstands the rigors of mowing but also promotes superior grass clipping discharge, ensuring a clean finish.

For comfort during use, the PD2042STA includes an ergonomically designed, high-back seat that provides support during extended mowing sessions. The soft-touch steering wheel enhances maneuverability, allowing for easy control around obstacles like flower beds and trees.

Maintenance is made simple with the inclusion of an easy-access battery and engine compartment, as well as a deck wash port that enables quick cleaning of the cutting deck after use. These features encourage regular upkeep, which extends the life of the mower and ensures optimal performance.

The Poulan PD2042STA also showcases a rugged design and sturdy construction, designed to handle rough terrains and provide longevity. With features like a large fuel tank and a front-mounted bumper, this riding mower is built for both efficiency and durability.

In summary, the Poulan PD2042STA is an excellent choice for homeowners seeking a dependable riding mower that combines power, comfort, and technological advancements. Its robust engine, user-friendly features, and high-quality construction make it a worthy investment for maintaining a beautiful lawn.
Top Page Image Contents