Poulan PD2042STA owner manual Tractor

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

ASSEMBLY

EDGE UP

 

BLADE

 

 

CENTER

 

HOLE

FLAT WASHER

LOCK WASHER

STAR

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 12

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PD2042STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatGauge Wheel BladeAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See aTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsMaintenance Service DatesGeneral Recommendations Before Each USETractor To Clean Battery and Terminals EngineBelts Transaxle CoolingCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points OFF Page Schematic Tractor - Model Number PD2042STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Drive Repair Parts Steering Assembly 180656 Wheel Steering Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck CAB Page Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD2042STA specifications

The Poulan PD2042STA is a robust and efficient riding lawn mower designed to meet the needs of homeowners with medium to large lawns. With a perfect blend of power, performance, and user-friendly features, this riding mower stands out in its category.

One of the key features of the Poulan PD2042STA is its powerful 42-inch cutting deck. This size allows for wide paths of grass to be trimmed in fewer passes, making lawn care quicker and more efficient. The mower is equipped with a reliable 19.5 horsepower Briggs & Stratton engine that provides ample power for cutting dense grass and maneuvering through varying terrains.

Ease of use is a hallmark of the PD2042STA, with its foot-pedal-operated automatic transmission. This technology allows for smooth acceleration and deceleration without the need for manual gear shifting. Mowing your lawn becomes a breeze, as the mower adapts effortlessly to the operator's speed preferences.

Additionally, the PD2042STA features a customizable cutting height ranging from 1 to 4 inches. This versatility ensures that users can achieve the desired lawn finish for different grass types and seasonal conditions. The mower also incorporates a durable steel deck that not only withstands the rigors of mowing but also promotes superior grass clipping discharge, ensuring a clean finish.

For comfort during use, the PD2042STA includes an ergonomically designed, high-back seat that provides support during extended mowing sessions. The soft-touch steering wheel enhances maneuverability, allowing for easy control around obstacles like flower beds and trees.

Maintenance is made simple with the inclusion of an easy-access battery and engine compartment, as well as a deck wash port that enables quick cleaning of the cutting deck after use. These features encourage regular upkeep, which extends the life of the mower and ensures optimal performance.

The Poulan PD2042STA also showcases a rugged design and sturdy construction, designed to handle rough terrains and provide longevity. With features like a large fuel tank and a front-mounted bumper, this riding mower is built for both efficiency and durability.

In summary, the Poulan PD2042STA is an excellent choice for homeowners seeking a dependable riding mower that combines power, comfort, and technological advancements. Its robust engine, user-friendly features, and high-quality construction make it a worthy investment for maintaining a beautiful lawn.
Top Page Image Contents