Poulan PD20PH42STA To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 8)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

CLEVIS PIN

FIG. 8

TO OPERATE MOWER (See Fig. 9)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

01843

FIG. 9

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly depress appropriate drive pedal to slowest set- ting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 6 and 10)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PD20PH42STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Mulching Mowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine BeltsTransaxle Cooling Transaxle Pump FluidCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check and Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Remove Hood and Grill Assembly See Fig To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points With attachment clutch Schematic Tractor - Model Number PD20PH42STA Product no 57NON-REMOVABLE Connections Removable Electrical KEY Part Description Chassis Tractor - Model Number PD20PH42STA Product no 57 Drive 17670508 Steering Assembly KEY Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresEngine 170771 Control, Throttle Mower Deck 182032X421 Mower Lift KEY Part NO. NO. Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD20PH42STA specifications

The Poulan PD20PH42STA is a versatile and powerful lawn tractor designed to meet the needs of homeowners with medium to large lawns. It offers a reliable and efficient solution for cutting grass, making yard maintenance a breeze. This model marries performance with ease of use, incorporating several features and technologies that set it apart in the lawn care market.

One of the standout characteristics of the Poulan PD20PH42STA is its robust engine. It is equipped with a dependable Poulan Pro 20-horsepower engine, which provides ample power for tackling tough lawn conditions. This engine is designed for enhanced fuel efficiency, allowing users to mow larger areas without the need for frequent refueling.

The 42-inch cutting deck is another notable feature of this lawn tractor. This size is ideal for maneuvering through residential lawns while providing sufficient coverage to reduce mowing time. The cutting deck is constructed from durable materials, ensuring longevity and reliability through numerous mowing seasons. Additionally, the deck offers multiple height adjustments, allowing users to achieve their desired grass length, catering to different lawn types and seasonal growth.

Another essential technology integrated into the PD20PH42STA is its hydrostatic transmission. This feature delivers smooth and effortless control, allowing operators to change speeds without the need for shifting gears. As a result, mowing becomes an intuitive experience, enabling the operator to focus on achieving a clean cut rather than managing complex controls.

The design of the Poulan PD20PH42STA prioritizes user comfort and convenience. Its ergonomically designed seat provides ample cushioning, enabling longer mowing sessions without discomfort. The tractor also includes easy-to-reach controls, and an integrated cup holder, ensuring that users can enjoy their mowing time without having to sacrifice comfort.

In terms of maintenance, the design of this lawn tractor makes it relatively simple. For instance, it features an access point for easy oil changes and a removable cutting deck, which simplifies blade maintenance and replacement.

Overall, the Poulan PD20PH42STA is an impressive lawn tractor that combines power, efficiency, and user-friendly features. Whether you’re tackling a large yard or managing overgrown grass, this model is built to deliver exceptional performance, making it a valuable tool for any homeowner looking to maintain a pristine lawn.
Top Page Image Contents