Poulan PD20PH42STA To Replace Mower Blade Drive Belt See Fig, To Check and Adjust Brake See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 24)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pul- leys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

MANDRELIDLER

PULLEYPULLEYS

MANDREL

PULLEY

FIG. 24

TO CHECK AND ADJUST BRAKE (See Fig. 25)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress brake pedal all the way down and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-3/4", loosen jam nut and turn nut “A” until distance becomes 1-3/4". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-3/4"

NUT “A”

JAM NUT

OPERATING

ARM

02537

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT

FIG. 25

TO REPLACE MOTION DRIVE BELT (See Fig. 26)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PD20PH42STA Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigCheck Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Transaxle Cooling EngineBelts Transaxle Pump FluidCleaning To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Figs Interlocks and RelaysTo Adjust Choke Control See Fig To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Tractor - Model Number PD20PH42STA Product no 57 SchematicNON-REMOVABLE Connections Removable Electrical KEY Part Description Chassis Tractor - Model Number PD20PH42STA Product no 57 Drive 17670508 Steering Assembly KEY Seat Assembly KEY Part NO. NO. DescriptionDecals Wheels and TiresEngine 170771 Control, Throttle Mower Deck 182032X421 Mower Lift KEY Part NO. NO. Description Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PD20PH42STA specifications

The Poulan PD20PH42STA is a versatile and powerful lawn tractor designed to meet the needs of homeowners with medium to large lawns. It offers a reliable and efficient solution for cutting grass, making yard maintenance a breeze. This model marries performance with ease of use, incorporating several features and technologies that set it apart in the lawn care market.

One of the standout characteristics of the Poulan PD20PH42STA is its robust engine. It is equipped with a dependable Poulan Pro 20-horsepower engine, which provides ample power for tackling tough lawn conditions. This engine is designed for enhanced fuel efficiency, allowing users to mow larger areas without the need for frequent refueling.

The 42-inch cutting deck is another notable feature of this lawn tractor. This size is ideal for maneuvering through residential lawns while providing sufficient coverage to reduce mowing time. The cutting deck is constructed from durable materials, ensuring longevity and reliability through numerous mowing seasons. Additionally, the deck offers multiple height adjustments, allowing users to achieve their desired grass length, catering to different lawn types and seasonal growth.

Another essential technology integrated into the PD20PH42STA is its hydrostatic transmission. This feature delivers smooth and effortless control, allowing operators to change speeds without the need for shifting gears. As a result, mowing becomes an intuitive experience, enabling the operator to focus on achieving a clean cut rather than managing complex controls.

The design of the Poulan PD20PH42STA prioritizes user comfort and convenience. Its ergonomically designed seat provides ample cushioning, enabling longer mowing sessions without discomfort. The tractor also includes easy-to-reach controls, and an integrated cup holder, ensuring that users can enjoy their mowing time without having to sacrifice comfort.

In terms of maintenance, the design of this lawn tractor makes it relatively simple. For instance, it features an access point for easy oil changes and a removable cutting deck, which simplifies blade maintenance and replacement.

Overall, the Poulan PD20PH42STA is an impressive lawn tractor that combines power, efficiency, and user-friendly features. Whether you’re tackling a large yard or managing overgrown grass, this model is built to deliver exceptional performance, making it a valuable tool for any homeowner looking to maintain a pristine lawn.
Top Page Image Contents