Poulan 96042012000, 433723 manual Transaxle Motion Control Lever Neutral Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 35)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2" in the direc- tion it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY

(REAR WHEEL ONLY)

Fig. 36

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO START ENGINE WITH A WEAK BATTERY (See Fig. 37)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

MOTION CONTROL LEVER

NEUTRAL

 

LOCK GATE

 

ADJUSTMENT

 

BOLT

Fig. 35

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 36)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

22

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 37

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB195H42LT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts SteeringTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Tire Pressure To Adjust Seat See FigCheck Deck Levelness Operation ROS on Know Your TractorPosition Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleTractor BatteryBlade Removal See Fig Engine AIR Filter Clean AIR ScreenCleaning MufflerTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

433723, 96042012000 specifications

The Poulan 96042012000,433723 is a robust and versatile gas-powered chainsaw designed for both casual users and professional woodworkers. Featuring a powerful engine, this chainsaw is capable of handling a variety of cutting tasks, making it an excellent choice for homeowners and landscapers alike.

One of the standout features of the Poulan 96042012000,433723 is its 42cc 2-cycle engine. This engine is engineered to deliver the perfect balance of power and efficiency, ensuring that you can tackle heavy-duty cutting jobs without overexerting yourself. The chainsaw boasts an impressive bar length commonly around 16 to 18 inches, enabling users to cut through thick branches and logs with ease.

The chainsaw also incorporates advanced technologies that enhance both performance and user experience. One of these technologies is the powerful cooling system, which helps maintain optimal operating temperatures during prolonged use. This feature not only extends the life of the engine but also ensures consistent cutting performance.

Moreover, the Poulan 96042012000,433723 features an automatic oiling system, allowing for effective lubrication of the chain and bar. This system helps to minimize friction, reducing wear and tear on the components, which leads to lower maintenance needs and a longer lifespan for the tool.

User comfort is also a priority in the design of this chainsaw. The ergonomically designed handle provides a secure grip, reducing fatigue during extended use. Coupled with the lightweight construction of the chainsaw, it becomes easy to maneuver, allowing for precise cutting and control in various applications.

Safety is another critical aspect of the Poulan 96042012000,433723. It includes features such as a chain brake for quick stopping power and a low kickback chain, which minimizes the risk of accidents. These safety enhancements make it suitable for users of all skill levels.

In conclusion, the Poulan 96042012000,433723 is a powerful, efficient, and user-friendly chainsaw that is ideal for a wide range of cutting tasks. With its robust engine, advanced technologies, and safety features, it stands out as a reliable tool for both personal and professional use in maintaining and managing outdoor spaces.
Top Page Image Contents