Poulan 96042012000, 433723 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 24

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PB195H42LT Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts SteeringAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidTo Adjust Seat See Fig Check Tire PressureCheck Deck Levelness Operation Know Your Tractor ROS onPosition HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Throttle Control See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate MowerBefore Starting the Engine To Operate on HillsTowing Carts and Other Attachments Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Removal See Fig Engine Clean AIR Screen CleaningAIR Filter MufflerService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTransmission Storage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

433723, 96042012000 specifications

The Poulan 96042012000,433723 is a robust and versatile gas-powered chainsaw designed for both casual users and professional woodworkers. Featuring a powerful engine, this chainsaw is capable of handling a variety of cutting tasks, making it an excellent choice for homeowners and landscapers alike.

One of the standout features of the Poulan 96042012000,433723 is its 42cc 2-cycle engine. This engine is engineered to deliver the perfect balance of power and efficiency, ensuring that you can tackle heavy-duty cutting jobs without overexerting yourself. The chainsaw boasts an impressive bar length commonly around 16 to 18 inches, enabling users to cut through thick branches and logs with ease.

The chainsaw also incorporates advanced technologies that enhance both performance and user experience. One of these technologies is the powerful cooling system, which helps maintain optimal operating temperatures during prolonged use. This feature not only extends the life of the engine but also ensures consistent cutting performance.

Moreover, the Poulan 96042012000,433723 features an automatic oiling system, allowing for effective lubrication of the chain and bar. This system helps to minimize friction, reducing wear and tear on the components, which leads to lower maintenance needs and a longer lifespan for the tool.

User comfort is also a priority in the design of this chainsaw. The ergonomically designed handle provides a secure grip, reducing fatigue during extended use. Coupled with the lightweight construction of the chainsaw, it becomes easy to maneuver, allowing for precise cutting and control in various applications.

Safety is another critical aspect of the Poulan 96042012000,433723. It includes features such as a chain brake for quick stopping power and a low kickback chain, which minimizes the risk of accidents. These safety enhancements make it suitable for users of all skill levels.

In conclusion, the Poulan 96042012000,433723 is a powerful, efficient, and user-friendly chainsaw that is ideal for a wide range of cutting tasks. With its robust engine, advanced technologies, and safety features, it stands out as a reliable tool for both personal and professional use in maintaining and managing outdoor spaces.
Top Page Image Contents