Poulan 96042012000 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

Utility knife

(2)

7/16" wrenches

Tire pressure gauge

(2) 1/2" wrenches

Pliers

(1)

9/16" wrench

 

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift seat to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT BOLT

LOCK

LARGE FLAT WASHER

WASHER

STEERING

WHEEL

 

STEERING

 

BOOT

LOWER

ADAPTER

 

STEERING

 

SHAFT

EXTENSION

 

SHAFT

Fig. 2

INSTALL SEAT (See Figs. 3 and 4)

LABEL

Fig. 1

ATTACH STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

6

Fig. 3

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB195H42LT General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts SteeringTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidTo Adjust Seat See Fig Check Tire PressureCheck Deck Levelness Operation Know Your Tractor ROS onPosition Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control See FigReverse Operation System ROS To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBattery TractorBlade Removal See Fig Engine AIR Filter Clean AIR ScreenCleaning MufflerService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionTroubleshooting Points Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty

433723, 96042012000 specifications

The Poulan 96042012000,433723 is a robust and versatile gas-powered chainsaw designed for both casual users and professional woodworkers. Featuring a powerful engine, this chainsaw is capable of handling a variety of cutting tasks, making it an excellent choice for homeowners and landscapers alike.

One of the standout features of the Poulan 96042012000,433723 is its 42cc 2-cycle engine. This engine is engineered to deliver the perfect balance of power and efficiency, ensuring that you can tackle heavy-duty cutting jobs without overexerting yourself. The chainsaw boasts an impressive bar length commonly around 16 to 18 inches, enabling users to cut through thick branches and logs with ease.

The chainsaw also incorporates advanced technologies that enhance both performance and user experience. One of these technologies is the powerful cooling system, which helps maintain optimal operating temperatures during prolonged use. This feature not only extends the life of the engine but also ensures consistent cutting performance.

Moreover, the Poulan 96042012000,433723 features an automatic oiling system, allowing for effective lubrication of the chain and bar. This system helps to minimize friction, reducing wear and tear on the components, which leads to lower maintenance needs and a longer lifespan for the tool.

User comfort is also a priority in the design of this chainsaw. The ergonomically designed handle provides a secure grip, reducing fatigue during extended use. Coupled with the lightweight construction of the chainsaw, it becomes easy to maneuver, allowing for precise cutting and control in various applications.

Safety is another critical aspect of the Poulan 96042012000,433723. It includes features such as a chain brake for quick stopping power and a low kickback chain, which minimizes the risk of accidents. These safety enhancements make it suitable for users of all skill levels.

In conclusion, the Poulan 96042012000,433723 is a powerful, efficient, and user-friendly chainsaw that is ideal for a wide range of cutting tasks. With its robust engine, advanced technologies, and safety features, it stands out as a reliable tool for both personal and professional use in maintaining and managing outdoor spaces.
Top Page Image Contents