Poulan 96042003501, 413437 manual Tractor, Blade Removal See Fig, Check Operator Presence System

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TIRES

•Maintain proper air pressure in all tires (See side of tire for proper air pressure).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 10)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

STAR

02

54

5

 

 

 

MANDREL

ASSEMBLY

BLADE BOLT

CENTER

(SPECIAL)

HOLE

 

FIG. 10

828

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PB19546LT ModelGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceIV. Towing Table of Contents Contents of Hardware Pack Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Unpack CartonInstall Seat See Figs Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills Before Starting the Engine To TransportTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Maintenance Lubrication ChartGeneral Recommendations ScheduleTractor Blade Removal See FigCheck Operator Presence System Check Reverse Operation ROS SystemBattery To Clean Battery and TerminalsTo Sharpen Blade See Fig BeltsLubrication EngineTo Change Engine OIL see Figs Cleaning To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Mower Drive Belt See FigTo Check Brake To Replace Motion Belt Drive See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopePage Page Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Défectueux estRalenti Entreposage Réglages ET Révision MoteurFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour CarrossageAVANT/ Roues DES Convergence 26 .FigCourroie Acer Rempl Pour ’ENTRAÎNEMENTFreins LES Vérifier Pour 25 .FIGTondeuse LA Niveau LE Ajuster Pour 23 .FIG22 .FIG 21 .FIG19 .FIG 18 .FIG17 .FIG 16 .FIGCourroie LA ET Tondeuse LA Installer Reglages ET RevisionFigs Voir D’ENTRAÎNEMENT Fig Voir Tondeuse LA Enlever PourEntretien 12 ET 11 .FIGS LES Voir Moteur DE L’HUILE Changer Pour Lubrification13 .FIG 12 .FIGTransmission LA DE Refroidissement Fig la Voir Lame LA AffilerTrapézoïdales Courroies Bornes LES ET Batterie LA Nettoyer PourLames DES Entretien Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Lubrification DE Tableau O I T a D N a M M O C E RUtilisation Chaque Avant Utilisation Tonte DE ConseilsMoteur LE Démarrer Pour DisengagedAccessoires Autres ’ESSENCE Réservoir LE RemplirMoteur DU D’HUILE Niveau LE Vérifier ET Charrettes DES Remorquer PourTondeuse LA Utiliser Pour Arrière Marche EN FonctionnementTondeuse DE Lames LES Arrêter Pour GEDGAZ DES Commande LA Utiliser Pour Fig la Voir Arrêter PourFig la Voir Mentne Tionsta DE Frein LE Engager PourDattachement Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier PA LA DE Tracteur LE Retirer PourDesman Com des fonction la et mentceplalemConnaître pour mentnetionfonc tionsec la Fig la Voir Batterie LA VérifierDU Tracteur LE Sortir Pour Pour Exigés Outils LESTionrecdi DE Volant LE Fixer Carton LE DeballerMontar SIN Piezas 28-27 Dépannage DE Guide Sommaire25-20 Réglages ET Révision Général Entretien Tracteurs des sécurité toute’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationLES Dans Fonctionnement PentesTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

413437, 96042003501 specifications

The Poulan 96042003501,413437 is a robust and versatile lawn mower that combines power, efficiency, and user-friendly features to cater to various lawn care needs. Designed for residential use, this model stands out due to its reliable performance and innovative technologies that enhance both functionality and convenience for homeowners.

One of the key features of the Poulan 96042003501,413437 is its powerful engine. Equipped with a reliable gas engine, it offers sufficient horsepower to tackle dense and overgrown grass, ensuring a clean and even cut every time. The engine starts easily, allowing users to get right to work without any delays. The mower's design also includes a solid cutting deck, which not only provides a wide cutting path for faster mowing but is also durable enough to withstand the rigors of regular use.

Another important feature of this model is its adjustable cutting height. Users can customize the height of the mower blades, making it easy to achieve the desired grass length based on individual lawn requirements and seasonal changes. This flexibility is essential for maintaining a healthy and aesthetically pleasing lawn.

The Poulan 96042003501,413437 also incorporates advanced mulching technology, allowing users to finely chop grass clippings and redistribute them back onto the lawn. This not only saves time by eliminating the need for bagging but also contributes to the lawn's health by returning valuable nutrients to the soil.

Safety features are paramount in the design of the Poulan mower. It includes a safety blade brake that halts the blades' rotation when the user disengages the control handle, preventing any accidental injuries. The mower is also equipped with ergonomic handles that ensure a comfortable grip, reducing fatigue during extended mowing sessions.

In terms of maintenance, the Poulan 96042003501,413437 is designed for easy access to critical components, facilitating routine checks and servicing. This ensures that the mower remains in optimal working condition over time.

Overall, the Poulan 96042003501,413437 is an efficient lawn care solution that combines power, versatility, safety, and ease of maintenance, making it an excellent choice for homeowners looking to maintain their lawns with minimal effort and maximum results. With its thoughtful design and innovative features, it stands as a reliable tool for achieving a beautifully manicured lawn.
Top Page Image Contents