Poulan 96042003501, 413437 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 24

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 26)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

Loosen adjustment bolt in front of the right rear wheel.

Position the gear shift lever in the neutral (N) posi- tion.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

GEARSHIFT LEVER

NEUTRAL LOCK GATE

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

ADJUSTMENT

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and

corrosion.24

FIG. 28

Image 24
Contents PB19546LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation Service III. ChildrenIV. Towing Table of Contents Contents of Hardware Pack Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Unpack CartonInstall Seat See Figs Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills Before Starting the Engine To TransportTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Maintenance Lubrication ChartGeneral Recommendations ScheduleTractor Blade Removal See FigCheck Operator Presence System Check Reverse Operation ROS SystemBattery To Clean Battery and TerminalsTo Sharpen Blade See Fig BeltsEngine LubricationTo Change Engine OIL see Figs Cleaning To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Mower Drive Belt See FigTo Check Brake To Replace Motion Belt Drive See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopePage Page Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Défectueux estRalenti Entreposage Réglages ET Révision MoteurFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour CarrossageAVANT/ Roues DES Convergence 26 .FigCourroie Acer Rempl Pour ’ENTRAÎNEMENTFreins LES Vérifier Pour 25 .FIGTondeuse LA Niveau LE Ajuster Pour 23 .FIG22 .FIG 21 .FIG19 .FIG 18 .FIG17 .FIG 16 .FIGCourroie LA ET Tondeuse LA Installer Reglages ET RevisionFigs Voir D’ENTRAÎNEMENT Fig Voir Tondeuse LA Enlever PourEntretien 12 ET 11 .FIGS LES Voir Moteur DE L’HUILE Changer Pour Lubrification13 .FIG 12 .FIGTransmission LA DE Refroidissement Fig la Voir Lame LA AffilerTrapézoïdales Courroies Bornes LES ET Batterie LA Nettoyer PourFig la Voir Lame LA Enlever Lames DES EntretienEN Fonctionnement DE Système ET O I T a D N a M M O C E R Lubrification DE TableauUtilisation Chaque Avant Utilisation Tonte DE ConseilsMoteur LE Démarrer Pour DisengagedAccessoires Autres ’ESSENCE Réservoir LE RemplirMoteur DU D’HUILE Niveau LE Vérifier ET Charrettes DES Remorquer PourTondeuse LA Utiliser Pour Arrière Marche EN FonctionnementTondeuse DE Lames LES Arrêter Pour GEDGAZ DES Commande LA Utiliser Pour Fig la Voir Arrêter PourFig la Voir Mentne Tionsta DE Frein LE Engager PourDattachement Propriété la de lendommagement Montage Correctement Sont Courroies LESToutes SI Vérifier Toutes SI Vérifier PA LA DE Tracteur LE Retirer PourDesman Com des fonction la et mentceplalemConnaître pour mentnetionfonc tionsec la Fig la Voir Batterie LA VérifierDU Tracteur LE Sortir Pour Pour Exigés Outils LESTionrecdi DE Volant LE Fixer Carton LE DeballerMontar SIN Piezas Sommaire 28-27 Dépannage DE Guide25-20 Réglages ET Révision Général Entretien Tracteurs des sécurité toute’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

413437, 96042003501 specifications

The Poulan 96042003501,413437 is a robust and versatile lawn mower that combines power, efficiency, and user-friendly features to cater to various lawn care needs. Designed for residential use, this model stands out due to its reliable performance and innovative technologies that enhance both functionality and convenience for homeowners.

One of the key features of the Poulan 96042003501,413437 is its powerful engine. Equipped with a reliable gas engine, it offers sufficient horsepower to tackle dense and overgrown grass, ensuring a clean and even cut every time. The engine starts easily, allowing users to get right to work without any delays. The mower's design also includes a solid cutting deck, which not only provides a wide cutting path for faster mowing but is also durable enough to withstand the rigors of regular use.

Another important feature of this model is its adjustable cutting height. Users can customize the height of the mower blades, making it easy to achieve the desired grass length based on individual lawn requirements and seasonal changes. This flexibility is essential for maintaining a healthy and aesthetically pleasing lawn.

The Poulan 96042003501,413437 also incorporates advanced mulching technology, allowing users to finely chop grass clippings and redistribute them back onto the lawn. This not only saves time by eliminating the need for bagging but also contributes to the lawn's health by returning valuable nutrients to the soil.

Safety features are paramount in the design of the Poulan mower. It includes a safety blade brake that halts the blades' rotation when the user disengages the control handle, preventing any accidental injuries. The mower is also equipped with ergonomic handles that ensure a comfortable grip, reducing fatigue during extended mowing sessions.

In terms of maintenance, the Poulan 96042003501,413437 is designed for easy access to critical components, facilitating routine checks and servicing. This ensures that the mower remains in optimal working condition over time.

Overall, the Poulan 96042003501,413437 is an efficient lawn care solution that combines power, versatility, safety, and ease of maintenance, making it an excellent choice for homeowners looking to maintain their lawns with minimal effort and maximum results. With its thoughtful design and innovative features, it stands as a reliable tool for achieving a beautifully manicured lawn.