Poulan 96012006802, 414754 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks,

GEARSHIFT LEVER

NEUTRAL LOCK GATE

flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

22

FIG. 23

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PO15542LT ModelGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Fig Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance Lubrication ChartBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST CeciDentretien Remarques Limitée Garantie Dépannage DE Guide Correction Cause ProblèmeRalenti Entreposage MoteurRéglages ET Révision DI LA DE L’ALIGNEMENT Régler Pour CarrossageAVANT/ Roues DES Convergence Vitesses DE Boîte LA DE Mentgechan’EN Courroie LA Remplacer Pour Courroie LA Remplacer PourTondeuse DE Lame DE Mentnetraî Transmission DE MENTNETRAÎD’ENLarrière À Devant DU Réglage DE Boîtier LE Niveau DE Mettre PourSedeuton Lautre À Côté DUN RéglageReglages ET Revision Tondeuse LA Installer PourTondeuse LA Enlever Pour ’ALLUMAGE Bougie Ligne EN Installé D’ESSENCE FiltreEntretien AIR À FiltreTrapézoïdales Courroies LubrificationTransmission LA DE Refroidissement Moteur DE L’HUILE Changer PourFig la Voir Lame LA Enlever Fig la Voir Lame LA AffilerEN Fonctionnement DE Système ET Lubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantUtilisation Tonte DE Conseils’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Accessoires AutresET Charrettes DES Remorquer Pour Pentes LES Dans Utiliser PourFig la Voir Arrêter Pour GAZ DES Commande LA Utiliser PourTeurtrac E R T O V R E S I L I T U T N E M M O C Fig la Voir Mentnetionsta DE Frein LE Engager Pour02829 Moteur Montage CON Pour Mentnetionfonc Tionsec LA DE Tracteur LE Retirer PourDesmancom DES LA Voir Rouler Faisant LE EN EttePalette LA DE Tracteur LE Retirer DE Avant DU Tracteur LE Sortir PourLE Pour Exigés Outils LES ToncarMontar SIN Piezas ClésClient DU Responsabilités SommaireProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsCom.poulan.www web site notre Visitez AUX Imprimé

414754, 96012006802 specifications

The Poulan 96012006802, 414754 is a versatile lawn maintenance tool designed for both homeowners and professional landscapers who demand efficiency and precision in their outdoor tasks. This powerful equipment combines advanced technology with robust construction to cater to various cutting needs.

One of the standout features of the Poulan 96012006802, 414754 is its powerful engine, which ensures reliable performance and longevity. This model is equipped with a patented 2-cycle engine that delivers not only ample power but also enhances fuel efficiency, allowing users to complete tasks without the constant need for refueling. This engine design minimizes the effort necessary to tackle thick grass and tough weeds, making it ideal for bigger yards or commercial applications.

Another significant characteristic of the Poulan 96012006802, 414754 is its lightweight design. Weighing less than many comparable models, it minimizes user fatigue during extended periods of operation. This is particularly beneficial for those who have larger lawns or are involved in extensive landscaping work. The ergonomic handle provides a comfortable grip, allowing for better maneuverability and control, reducing strain on the hands and arms.

The cutting mechanism of the Poulan 96012006802, 414754 is noteworthy for its efficiency. It is designed with a durable cutting blade that can handle a variety of grass types and thicknesses. The adjustable cutting height feature allows users to select their preferred grass length, creating a custom lawn aesthetic while promoting healthy growth.

Furthermore, this model incorporates safety features that enhance user protection. A throttle control system ensures that the engine revs are optimized for various tasks, while also providing an easy way to shut off the power immediately when needed.

In summary, the Poulan 96012006802, 414754 presents an excellent option for those seeking a reliable, powerful, and user-friendly lawn maintenance tool. With its efficient engine, lightweight design, adjustable cutting height, and enhanced safety features, it stands out in the competitive landscape of gardening equipment. Whether for residential upkeep or professional landscaping projects, this model promises to deliver exceptional performance and results.
Top Page Image Contents