Poulan 96012006802 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(1) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK

WASHER

LARGE FLAT WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION SHAFT

LOWER

STEERING

SHAFT

 

 

 

19

TAB

0

2

8

SLOTS

FIG. 1

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PO15542LT ModelSafe Operation Practices for Ride-On Mowers General OperationII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Fig Check Battery See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Maintenance Lubrication ChartTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig To Remove Mower See FigTo Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST CeciDentretien Remarques Limitée Garantie Dépannage DE Guide Correction Cause ProblèmeRalenti Entreposage MoteurRéglages ET Révision DI LA DE L’ALIGNEMENT Régler Pour CarrossageAVANT/ Roues DES Convergence Vitesses DE Boîte LA DE Mentgechan’EN Courroie LA Remplacer Pour Courroie LA Remplacer PourTondeuse DE Lame DE Mentnetraî Transmission DE MENTNETRAÎD’ENLarrière À Devant DU Réglage DE Boîtier LE Niveau DE Mettre PourSedeuton Lautre À Côté DUN RéglageTondeuse LA Installer Pour Reglages ET RevisionTondeuse LA Enlever Pour ’ALLUMAGE Bougie Ligne EN Installé D’ESSENCE FiltreEntretien AIR À FiltreTrapézoïdales Courroies LubrificationTransmission LA DE Refroidissement Moteur DE L’HUILE Changer PourFig la Voir Lame LA Affiler Fig la Voir Lame LA EnleverEN Fonctionnement DE Système ET Lubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantUtilisation Tonte DE Conseils’ESSENCE Réservoir LE Remplir Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour Moteur DU D’HUILE Niveau LE VérifierTracteur LE Transporter Pour Accessoires AutresET Charrettes DES Remorquer Pour Pentes LES Dans Utiliser PourFig la Voir Arrêter Pour GAZ DES Commande LA Utiliser PourTeurtrac E R T O V R E S I L I T U T N E M M O C Fig la Voir Mentnetionsta DE Frein LE Engager Pour02829 Moteur Montage CON Pour Mentnetionfonc Tionsec LA DE Tracteur LE Retirer PourDesmancom DES LA Voir Rouler Faisant LE EN EttePalette LA DE Tracteur LE Retirer DE Avant DU Tracteur LE Sortir PourLE Pour Exigés Outils LES ToncarMontar SIN Piezas ClésSommaire Client DU ResponsabilitésProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsCom.poulan.www web site notre Visitez AUX Imprimé

414754, 96012006802 specifications

The Poulan 96012006802, 414754 is a versatile lawn maintenance tool designed for both homeowners and professional landscapers who demand efficiency and precision in their outdoor tasks. This powerful equipment combines advanced technology with robust construction to cater to various cutting needs.

One of the standout features of the Poulan 96012006802, 414754 is its powerful engine, which ensures reliable performance and longevity. This model is equipped with a patented 2-cycle engine that delivers not only ample power but also enhances fuel efficiency, allowing users to complete tasks without the constant need for refueling. This engine design minimizes the effort necessary to tackle thick grass and tough weeds, making it ideal for bigger yards or commercial applications.

Another significant characteristic of the Poulan 96012006802, 414754 is its lightweight design. Weighing less than many comparable models, it minimizes user fatigue during extended periods of operation. This is particularly beneficial for those who have larger lawns or are involved in extensive landscaping work. The ergonomic handle provides a comfortable grip, allowing for better maneuverability and control, reducing strain on the hands and arms.

The cutting mechanism of the Poulan 96012006802, 414754 is noteworthy for its efficiency. It is designed with a durable cutting blade that can handle a variety of grass types and thicknesses. The adjustable cutting height feature allows users to select their preferred grass length, creating a custom lawn aesthetic while promoting healthy growth.

Furthermore, this model incorporates safety features that enhance user protection. A throttle control system ensures that the engine revs are optimized for various tasks, while also providing an easy way to shut off the power immediately when needed.

In summary, the Poulan 96012006802, 414754 presents an excellent option for those seeking a reliable, powerful, and user-friendly lawn maintenance tool. With its efficient engine, lightweight design, adjustable cutting height, and enhanced safety features, it stands out in the competitive landscape of gardening equipment. Whether for residential upkeep or professional landscaping projects, this model promises to deliver exceptional performance and results.
Top Page Image Contents