Poulan 414754, 96012006802 manual Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SHOULDER

BOLT

 

SEAT PAN

 

FLAT WASHER

 

LOCK WASHER

 

 

02465

ADJUSTMENT

 

BOLT

 

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

TERMINAL

TERMINAL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model PO15542LTGeneral Operation Safe Operation Practices for Ride-On MowersII. Slope Operation IV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Unpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Lubrication Chart MaintenanceBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Remove Mower See Fig To Install Mower See FigFRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig To Adjust Steering Wheel ALIGN- MentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Parts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESDentretien Remarques Limitée Garantie Correction Cause Problème Dépannage DE GuideRalenti Moteur EntreposageRéglages ET Révision Vitesses DE Boîte LA DE Mentgechan CarrossageAVANT/ Roues DES Convergence DI LA DE L’ALIGNEMENT Régler PourTransmission DE MENTNETRAÎD’EN Courroie LA Remplacer PourTondeuse DE Lame DE Mentnetraî ’EN Courroie LA Remplacer PourLautre À Côté DUN Réglage DE Boîtier LE Niveau DE Mettre PourSedeuton Larrière À Devant DU RéglageReglages ET Revision Tondeuse LA Installer PourTondeuse LA Enlever Pour AIR À Filtre Ligne EN Installé D’ESSENCE FiltreEntretien ’ALLUMAGE BougieMoteur DE L’HUILE Changer Pour LubrificationTransmission LA DE Refroidissement Trapézoïdales CourroiesFig la Voir Lame LA Enlever Fig la Voir Lame LA AffilerEN Fonctionnement DE Système ET Utilisation Chaque Avant Recommandations LESGénérales Lubrification DE TableauTonte DE Conseils UtilisationMoteur DU D’HUILE Niveau LE Vérifier Moteur LE Démarrer DE AvantMoteur LE Démarrer Pour ’ESSENCE Réservoir LE RemplirPentes LES Dans Utiliser Pour Accessoires AutresET Charrettes DES Remorquer Pour Tracteur LE Transporter PourFig la Voir Mentnetionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourTeurtrac E R T O V R E S I L I T U T N E M M O C Fig la Voir Arrêter Pour02829 Moteur Montage LA Voir Rouler Faisant LE EN Ette LA DE Tracteur LE Retirer PourDesmancom DES CON Pour Mentnetionfonc TionsecToncar DU Tracteur LE Sortir PourLE Pour Exigés Outils LES Palette LA DE Tracteur LE Retirer DE AvantClés Montar SIN PiezasClient DU Responsabilités SommaireProduit DE Spécifications Général Entretien EntretienRemorquage EnfantsTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement Général FonctionnementAUX Imprimé Com.poulan.www web site notre Visitez

414754, 96012006802 specifications

The Poulan 96012006802, 414754 is a versatile lawn maintenance tool designed for both homeowners and professional landscapers who demand efficiency and precision in their outdoor tasks. This powerful equipment combines advanced technology with robust construction to cater to various cutting needs.

One of the standout features of the Poulan 96012006802, 414754 is its powerful engine, which ensures reliable performance and longevity. This model is equipped with a patented 2-cycle engine that delivers not only ample power but also enhances fuel efficiency, allowing users to complete tasks without the constant need for refueling. This engine design minimizes the effort necessary to tackle thick grass and tough weeds, making it ideal for bigger yards or commercial applications.

Another significant characteristic of the Poulan 96012006802, 414754 is its lightweight design. Weighing less than many comparable models, it minimizes user fatigue during extended periods of operation. This is particularly beneficial for those who have larger lawns or are involved in extensive landscaping work. The ergonomic handle provides a comfortable grip, allowing for better maneuverability and control, reducing strain on the hands and arms.

The cutting mechanism of the Poulan 96012006802, 414754 is noteworthy for its efficiency. It is designed with a durable cutting blade that can handle a variety of grass types and thicknesses. The adjustable cutting height feature allows users to select their preferred grass length, creating a custom lawn aesthetic while promoting healthy growth.

Furthermore, this model incorporates safety features that enhance user protection. A throttle control system ensures that the engine revs are optimized for various tasks, while also providing an easy way to shut off the power immediately when needed.

In summary, the Poulan 96012006802, 414754 presents an excellent option for those seeking a reliable, powerful, and user-friendly lawn maintenance tool. With its efficient engine, lightweight design, adjustable cutting height, and enhanced safety features, it stands out in the competitive landscape of gardening equipment. Whether for residential upkeep or professional landscaping projects, this model promises to deliver exceptional performance and results.
Top Page Image Contents