Poulan 418791 manual To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE (See Fig. 21)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

TO REPLACE MOTION DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

01513

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHO- RIZED SERVICE CENTER/DEPARTMENT

FIG. 21

FIG. 22

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 23)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine

21 off.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model PB195H42LTXSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Steering Wheel Unassembled PartsSeat Keys Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Install Seat See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROS See FigTo Operate on Hills To Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP RunningLubrication Chart MaintenanceBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Lubrication BatteryTransaxle Pump Fluid BeltsClean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when HOP Outdoor Products Customer Service DeptCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN UNE Pliez EST Ceci Degrés Suivant LESDentretien Notes Dept Service Customer Products Outdoor Canada Au AutoriséGarantie cette de exclus sont normal l’entretien et Conducteur le lorsque Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage MoteurTracteur Moteur Reglages ET RevisionRossage LA DE ENLEVEMENT/REMPLACEMENTAVANT/CAR Roues DES Convergence LA DE L’ALIGNEMENT Régler Pour’EN Courroie LA Remplacer Pour Fig la VoirFrein LE Régler ET Contrôler Pour Transmission DE MentnetraîTondeuse DE Lame DE MENTNETRAÎD’EN Courroie Acer Rempl Pour15 .FIG Tondeuse DE Boîtier LE Niveler Pour’ALLUMAGE Bougie EntretienAIR À Filtre ’AIR Tamis LE NettoyerTransmission LA DE Refroidissement Sionmistrans LA DE Moteur FluideFig la Voir Lame LA Affiler Trapézoïdales CourroiesEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverGénérales Recommandations LESLubrification DE Tableau Utilisation Chaque AvantTondre DE Conseils UtilisationTransmission LA Purger QuetiMoteur LE Démarrer DE Avant Tracteur LE Transporter Pour Et 4 .Fig les VoirPentes LES Dans Utiliser Pour Tondeuse LA Utiliser PourTeurtrac Votre Utiliser Comment GAZ DES Commande LA Utiliser PourFig la Voir Arrêter Pour Fig la Voir Mentnetionsta DE Frein LE Engager PourLSW02838 ’EMBRAYAGE NI DE EST Tondeuse LA SI Vérifier MontageDesmancom des tionfonc la et Tionsec la Voir Conduisant LE EN TeletVotre Monter Comment Fig la Voir Siège LE InstallerDesman Com des fonction la et mentceplalemDU Tracteur LE Sortir Pour Palette LA DE Tracteur LE Retirer DE AvantToncar Pente-Guide Montées NON PiécesClient DU Responsabilités SommaireProduit DE Spécifications CCA .MIN AMP/HRRemorquage EntretienEnfants Général EntretienPEN LES Dans Fonctionnement TESGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsPBA195H42LTX Modèle Com.poulan.www web site notre VisitezAUX Imprimé

418791, 96012008500 specifications

The Poulan 96012008500, 418791 is a high-quality string trimmer designed to cater to the needs of both homeowners and professional landscapers. This versatile tool is constructed with a focus on power, efficiency, and user comfort, making it an ideal choice for maintaining lawns, gardens, and other outdoor spaces.

One of the standout features of the Poulan 96012008500 is its robust 25cc, 2-cycle engine. This powerful engine offers excellent cutting performance while maintaining a lightweight design, allowing for easy maneuverability during use. It is engineered to provide optimal performance, enabling users to tackle tough jobs with ease. The engine's construction also emphasizes fuel efficiency, which promotes longer run times and reduces the frequency of refueling.

In addition to its impressive engine, the trimmer incorporates a dual-line cutting system with a bump-feed head. This feature allows for quick and easy line advancement with a simple tap on the ground, ensuring uninterrupted operation as users trim around obstacles and edges. The dual-line setup offers a wider cutting path, enhancing efficiency and reducing the time needed to complete lawn maintenance tasks.

Ergonomics play a crucial role in the design of the Poulan 96012008500. Equipped with an adjustable handle, users can easily customize the trimmer to their height for maximum comfort. The cushioned grip further minimizes fatigue during prolonged use, making it suitable for extended trimming sessions. The lightweight design of the trimmer also contributes to ease of use, reducing strain on the arms and back.

Another noteworthy technology implemented in this trimmer is the "Easy Start" feature, which simplifies the starting process. With this technology, users can quickly start the machine with minimal effort, allowing for a stress-free experience, especially for those who may have difficulty with traditional starting mechanisms.

Durability is also a key component of the Poulan 96012008500. It is crafted from high-quality materials resistant to wear and tear, ensuring that the trimmer can withstand the rigors of regular use. This reliability makes it a sound investment for anyone looking to maintain their yard or garden effectively.

Overall, the Poulan 96012008500, 418791 combines powerful performance, user-friendly features, and ergonomic design. Whether you are a homeowner aiming to keep your lawn neat or a professional landscaper needing a reliable tool, this string trimmer offers the performance and durability necessary for optimal efficiency in outdoor maintenance tasks.
Top Page Image Contents