Poulan 96012008500, 418791 manual Check Tire Pressure, Check Deck Levelness, Check Brake System

Page 8

ASSEMBLY

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown on tires.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- FORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged.

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving tractor, be sure freewheel control is in “transmission engaged” position (see “TO TRANS- PORT” in the Operation section of this manual).

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls, their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓Be sure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

✓It is important to purge the transmission before op- erating your tractor for the first time. Follow proper starting and transmission purging instructions (See “TO START ENGINE” and “PURGE TRANSMISSION” in the Operation section of this manual).

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents PB195H42LTX ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Unassembled Parts Steering WheelSeat Keys Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate Mower See FigReverse Operation System ROS See Fig Before Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP RunningMaintenance Lubrication ChartTractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemLubrication Battery EngineTransaxle Pump Fluid BeltsCleaning Clean AIR ScreenAIR Filter MufflerService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Outdoor Products Customer Service Dept HOPCanada contact Stevens Creek Road Terry Fox Way Augusta, GA 30907 USAService Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés Suivant LES UNE Pliez EST CeciDentretien Notes Garantie cette de exclus sont normal l’entretien et Dept Service Customer Products Outdoor Canada AuAutorisé Dépannage DE Guide Conducteur le lorsqueLame de mandrin le Remplacez Tordu est lame de mandrin Un Tracteur EntreposageMoteur Reglages ET Revision MoteurLA DE ENLEVEMENT/REMPLACEMENT RossageAVANT/CAR Roues DES Convergence LA DE L’ALIGNEMENT Régler PourFig la Voir ’EN Courroie LA Remplacer PourFrein LE Régler ET Contrôler Pour Transmission DE MentnetraîCourroie Acer Rempl Pour Tondeuse DE Lame DE MENTNETRAÎD’ENTondeuse DE Boîtier LE Niveler Pour 15 .FIGEntretien ’ALLUMAGE BougieAIR À Filtre ’AIR Tamis LE NettoyerSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementFig la Voir Lame LA Affiler Trapézoïdales CourroiesFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETRecommandations LES GénéralesLubrification DE Tableau Utilisation Chaque AvantUtilisation Tondre DE ConseilsTransmission LA Purger QuetiMoteur LE Démarrer DE Avant Et 4 .Fig les Voir Tracteur LE Transporter PourPentes LES Dans Utiliser Pour Tondeuse LA Utiliser PourGAZ DES Commande LA Utiliser Pour Teurtrac Votre Utiliser CommentFig la Voir Arrêter Pour Fig la Voir Mentnetionsta DE Frein LE Engager PourLSW02838 ’EMBRAYAGE Montage NI DE EST Tondeuse LA SI VérifierDesmancom des tionfonc la et Tionsec la Voir Conduisant LE EN TeletFig la Voir Siège LE Installer Votre Monter CommentDesman Com des fonction la et mentceplalemToncar DU Tracteur LE Sortir PourPalette LA DE Tracteur LE Retirer DE Avant Montées NON Piéces Pente-GuideSommaire Client DU ResponsabilitésProduit DE Spécifications CCA .MIN AMP/HREntretien RemorquageEnfants Général EntretienTES PEN LES Dans FonctionnementGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé PBA195H42LTX ModèleCom.poulan.www web site notre Visitez

418791, 96012008500 specifications

The Poulan 96012008500, 418791 is a high-quality string trimmer designed to cater to the needs of both homeowners and professional landscapers. This versatile tool is constructed with a focus on power, efficiency, and user comfort, making it an ideal choice for maintaining lawns, gardens, and other outdoor spaces.

One of the standout features of the Poulan 96012008500 is its robust 25cc, 2-cycle engine. This powerful engine offers excellent cutting performance while maintaining a lightweight design, allowing for easy maneuverability during use. It is engineered to provide optimal performance, enabling users to tackle tough jobs with ease. The engine's construction also emphasizes fuel efficiency, which promotes longer run times and reduces the frequency of refueling.

In addition to its impressive engine, the trimmer incorporates a dual-line cutting system with a bump-feed head. This feature allows for quick and easy line advancement with a simple tap on the ground, ensuring uninterrupted operation as users trim around obstacles and edges. The dual-line setup offers a wider cutting path, enhancing efficiency and reducing the time needed to complete lawn maintenance tasks.

Ergonomics play a crucial role in the design of the Poulan 96012008500. Equipped with an adjustable handle, users can easily customize the trimmer to their height for maximum comfort. The cushioned grip further minimizes fatigue during prolonged use, making it suitable for extended trimming sessions. The lightweight design of the trimmer also contributes to ease of use, reducing strain on the arms and back.

Another noteworthy technology implemented in this trimmer is the "Easy Start" feature, which simplifies the starting process. With this technology, users can quickly start the machine with minimal effort, allowing for a stress-free experience, especially for those who may have difficulty with traditional starting mechanisms.

Durability is also a key component of the Poulan 96012008500. It is crafted from high-quality materials resistant to wear and tear, ensuring that the trimmer can withstand the rigors of regular use. This reliability makes it a sound investment for anyone looking to maintain their yard or garden effectively.

Overall, the Poulan 96012008500, 418791 combines powerful performance, user-friendly features, and ergonomic design. Whether you are a homeowner aiming to keep your lawn neat or a professional landscaper needing a reliable tool, this string trimmer offers the performance and durability necessary for optimal efficiency in outdoor maintenance tasks.
Top Page Image Contents