Poulan 417217 manual Service and Adjustments, To Remove Mower See Fig, To Install Mower See -21

Page 18

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 17)

•Place attachment clutch in “DISENGAGED” position.

•Lower attachment lift lever to its lowest position.

•Roll belt off engine pulley (M) and belt keepers (G).

•Remove retainer spring (K), slide collar (L) off and push housing guide (P) out of bracket.

•Remove clutch cable spring (Q) from idler arm (R).

•Disconnect front link (E) from mower - remove retainer spring and washer.

•Go to either side of mower and disconnect mower suspension arm (A) from chassis pin (B) and rear lift link (C) from rear mower bracket (D) - remove retainer springs and washers.

CAUTION: AFTER REAR LIFT LINKS

ARE DISCONNECTED, THE ATTACH-

MENT LIFT LEVER WILL BE SPRING

LOADED. HAVE A TIGHT GRIP ON LIFT

LEVER WHEN CHANGING POSITION

OF THE LEVER.

•Slide mower out from under right side of tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINK (E) AND REAR LIFT LIKS

(C) FROM TRACTOR AND HOOK THE CLUTCH SPRING

(Q)INTO THE CABLE GUIDE ON FRONT EDGE OF LOWER DASH.

TO INSTALL MOWER (See Fig.17-21)

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: LIFT LEVER IS SPRING

LOADED. HAVE A TIGHT GRIP ON

LIFT LEVER, LOWER IT SLOWLY AND

ENGAGE IN LOWEST POSITION.

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

•ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

•Repeat on opposite side of tractor.

•ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin (D) on rear mower bracket and secure with washer and retainer spring.

G M F

Q RG

P

A E

B

C

K

L D

FIG. 17

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents PB195H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor DHEHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsService and Adjustments To Install Mower See -21To Remove Mower See Fig Service and Adjustments To Level Mower Turn nut right Turn nut left To raise mower To lower mowerTo Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty L5V 3E4Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Autorisé Garantie cette de exclus sont normal l’entretien etInitiale d’achat date la de compter à jours 90 dix Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Correction Cause ProblèmeLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage MoteurTracteur Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour MoteurFig la Voir Batterie LA Replacer Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE Freins LES Vérifier Pour Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour 27 .FIG24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG18 .FIG 21 .FIG 19 .FIG20 .FIG Coin le Soulevez C Arrières Bielles LES AttachezTondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFig Voir 17 .FIG’ALLUMAGE Bougie EntretienFig la Voir Moteur DE D’HUILE FiltreSionmistrans LA DE Moteur Fluide AIR À Filtre’AIR Tamis LE Nettoyer Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantUtilisation Tondre DE Conseils12 .FIG Quetimaauto Transmission LA PurgerMoteur LE Démarrer Pour Sion Transmis DE RéchauffementMoteur LE Démarrer DE Avant 11 et 3 .Fig les VoirMAR EN Fonctionnement DE Système 10 .FIG Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesDE Régulateur LE Utiliser Comment GAZ DES Commande LA Utiliser PourVitess Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Montage Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Siège LE AjustezSommaire Client DU ResponsabilitésProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé Avertissement

417217 specifications

The Poulan 417217 is a robust and versatile chainsaw that caters to both professional and amateur users alike. Known for its reliability and ease of use, the Poulan 417217 has gained a reputation in the market as an efficient tool for various cutting tasks, from trimming trees to felling larger timber.

At the heart of the Poulan 417217 is its powerful engine, typically featuring a 42cc two-stroke engine that provides a balance between power and efficiency. This engine delivers a sufficient horsepower output to tackle demanding jobs while maintaining manageable weight for user comfort. The advanced engine design also ensures reduced emissions, making it an environmentally-friendly option for users concerned about their carbon footprint.

One of the standout features of the Poulan 417217 is its ease of starting. The chainsaw is equipped with an automatic oiler system that keeps the chain lubricated during use, prolonging its lifespan and maintaining optimal performance. The quick-release air filter system allows for simple maintenance and easy access when cleaning, which is crucial for the longevity and reliability of the tool.

The chainsaw's 18-inch cutting bar is designed for efficient cutting and maneuverability. It makes quick work of branches and logs, providing smooth performance on various materials. Coupled with a low-kickback chain, safety becomes a priority, helping to prevent accidents during operation.

Ergonomically designed handles enhance user comfort and control, minimizing fatigue during extended periods of use. The vibration dampening technology integrated into the handle design further contributes to an enjoyable user experience by reducing vibrations that can lead to hand fatigue.

The Poulan 417217 also features a combination of a primer bulb and a choke for quick and easy starting, allowing the user to begin their task with minimal delay. Additionally, the chainsaw's lightweight design allows for easy transport and prolonged use without excessive strain.

In summary, the Poulan 417217 offers a combination of power, safety, and user-friendly features, making it an ideal choice for anyone seeking a dependable chainsaw. Whether you are a seasoned professional or a novice, the 417217 equips you with the performance needed to achieve your cutting goals efficiently and safely.
Top Page Image Contents