Poulan 417217 manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 22

SERVICE AND ADJUSTMENTS

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

 

 

 

 

 

FULLY CHARGED

BATTERY

 

 

 

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIG. 29

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

DISCARD TERMINAL

KEPS NUT

HEX BOLT

 

PROTECTIVE CAPS

 

 

 

TERMINAL

COVER

NEGATIVE (BLACK) CABLE

POSITIVE (RED) CABLE

03037

22

FIG. 30

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PB195H46YT ModelGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor DHEHOW to USE Your Tractor StoppingSystem Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See -21 Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower Turn nut right Turn nut left To raise mower To lower mowerTo Check Brake To Replace Mower Drive Belt See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Suggested Guide for Sighting Slopes for Safe Operation Limited Warranty L5V 3E4Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Garantie cette de exclus sont normal l’entretien et AutoriséInitiale d’achat date la de compter à jours 90 dix Degrés Suivant LES UNE Pliez EST CeciDépannage DE Guide Correction Cause ProblèmeLame de mandrin le Remplacez Tordu est lame de mandrin Un Moteur EntreposageTracteur Reglages ET Revision Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour MoteurFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Fig la Voir Batterie LA ReplacerAvant Roue LA DE PINCEMENT/CARROSSAGE Freins LES Vérifier Pour Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour 27 .FIG24 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 23 .FIG18 .FIG 21 .FIG 19 .FIG20 .FIG Coin le Soulevez C Arrières Bielles LES AttachezTondeuse LA Enlever Pour Courroie LA ET Tondeuse LA InstallerFig Voir 17 .FIG’ALLUMAGE Bougie EntretienFig la Voir Moteur DE D’HUILE FiltreSionmistrans LA DE Moteur Fluide AIR À Filtre’AIR Tamis LE Nettoyer Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Recommandations LESGénérales Utilisation Chaque AvantTondre DE Conseils Utilisation12 .FIG Quetimaauto Transmission LA PurgerMoteur LE Démarrer Pour Sion Transmis DE Réchauffement11 et 3 .Fig les Voir Moteur LE Démarrer DE AvantMAR EN Fonctionnement DE Système 10 .FIG Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour Système DU CaractéristiquesDE Régulateur LE Utiliser Comment GAZ DES Commande LA Utiliser PourVitess Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Desmancom des tionfonc la et MontageLA DE Tracteur LE Retirer Pour Fig la Voir Batterie LA Vérifier Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Siège LE AjustezClient DU Responsabilités SommaireProduit DE Spécifications Enfants EntretienRemorquage Général EntretienGénéral Fonctionnement PentesLES Dans Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAUX Imprimé Avertissement

417217 specifications

The Poulan 417217 is a robust and versatile chainsaw that caters to both professional and amateur users alike. Known for its reliability and ease of use, the Poulan 417217 has gained a reputation in the market as an efficient tool for various cutting tasks, from trimming trees to felling larger timber.

At the heart of the Poulan 417217 is its powerful engine, typically featuring a 42cc two-stroke engine that provides a balance between power and efficiency. This engine delivers a sufficient horsepower output to tackle demanding jobs while maintaining manageable weight for user comfort. The advanced engine design also ensures reduced emissions, making it an environmentally-friendly option for users concerned about their carbon footprint.

One of the standout features of the Poulan 417217 is its ease of starting. The chainsaw is equipped with an automatic oiler system that keeps the chain lubricated during use, prolonging its lifespan and maintaining optimal performance. The quick-release air filter system allows for simple maintenance and easy access when cleaning, which is crucial for the longevity and reliability of the tool.

The chainsaw's 18-inch cutting bar is designed for efficient cutting and maneuverability. It makes quick work of branches and logs, providing smooth performance on various materials. Coupled with a low-kickback chain, safety becomes a priority, helping to prevent accidents during operation.

Ergonomically designed handles enhance user comfort and control, minimizing fatigue during extended periods of use. The vibration dampening technology integrated into the handle design further contributes to an enjoyable user experience by reducing vibrations that can lead to hand fatigue.

The Poulan 417217 also features a combination of a primer bulb and a choke for quick and easy starting, allowing the user to begin their task with minimal delay. Additionally, the chainsaw's lightweight design allows for easy transport and prolonged use without excessive strain.

In summary, the Poulan 417217 offers a combination of power, safety, and user-friendly features, making it an ideal choice for anyone seeking a dependable chainsaw. Whether you are a seasoned professional or a novice, the 417217 equips you with the performance needed to achieve your cutting goals efficiently and safely.
Top Page Image Contents