Poulan 417217 manual Troubleshooting Points, Problem Cause Correction

Page 25

TROUBLESHOOTING POINTS

PROBLEM

 

CAUSE

 

CORRECTION

 

 

 

 

 

 

 

 

 

 

 

 

 

Will not start

 

1.

Out of fuel.

 

1.

Fill fuel tank.

 

 

 

 

2.

Engine not “CHOKED” properly.

 

2.

See “TO START ENGINE” in Operation section.

 

 

 

 

3.

Engine flooded.

 

3.

Wait several minutes before attempting to start.

 

 

 

 

4.

Bad spark plug.

 

4.

Replace spark plug.

 

 

 

 

5.

Weak or dead battery.

 

5.

Recharge or replace battery.

 

 

 

 

6.

Dirty air filter.

 

6.

Clean/replace air filter.

 

 

 

 

7.

Dirty fuel filter.

 

7.

Replace fuel filter.

 

 

 

 

8.

Water in fuel.

 

8.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

 

9.

Loose or damaged wiring.

 

9.

Check all wiring.

 

 

 

 

10.

Carburetor out of adjustment.

 

10.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

 

 

section.

 

 

 

 

11.

Engine valves out of adjustment.

 

11.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Hard to start

 

1.

Dirty air filter.

 

1.

Clean/replace air filter.

 

 

 

 

2.

Bad spark plug.

 

2.

Replace spark plug.

 

 

 

 

3.

Weak or dead battery.

 

3.

Recharge or replace battery.

 

 

 

 

4.

Dirty fuel filter.

 

4.

Replace fuel filter.

 

 

 

 

5.

Stale or dirty fuel.

 

5.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

 

6.

Loose or damaged wiring.

 

6.

Check all wiring.

 

 

 

 

7.

Carburetor out of adjustment.

 

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

 

 

section.

 

 

 

 

8.

Engine valves out of adjustment.

 

8.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Engine will not turn over

 

1.

Brake pedal not depressed.

 

1.

Depress brake pedal.

 

 

 

 

2.

Attachment clutch is engaged.

 

2.

Disengage attachment clutch.

 

 

 

 

3.

Weak or dead battery.

 

3.

Recharge or replace battery.

 

 

 

 

4.

Blown fuse.

 

4.

Replace fuse.

 

 

 

 

5.

Corroded battery terminals.

 

5.

Clean battery terminals.

 

 

 

 

6.

Loose or damaged wiring.

 

6.

Check all wiring.

 

 

 

 

7.

Faulty ignition switch.

 

7.

Check/replace ignition switch.

 

 

 

 

8.

Faulty solenoid or starter.

 

8.

Check/replace solenoid or starter.

 

 

 

 

9.

Faulty operator presence switch(es).

 

9.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Engine clicks but will not

 

1.

Weak or dead battery.

 

1.

Recharge or replace battery.

 

start

 

2.

Corroded battery terminals.

 

2.

Clean battery terminals.

 

 

 

 

3.

Loose or damaged wiring.

 

3.

Check all wiring.

 

 

 

 

4.

Faulty solenoid or starter.

 

4.

Check/replace solenoid or starter.

 

 

 

 

 

 

 

 

 

 

Loss of power

 

1.

Cutting too much grass/too fast.

 

1.

Raise cutting height/reduce speed.

 

 

 

 

2.

Throttle in “CHOKE” position.

 

2.

Adjust throttle control.

 

 

 

 

3.

Build-up of grass, leaves and trash under mower.

 

3.

Clean underside of mower housing.

 

 

 

 

4.

Dirty air filter.

 

4.

Clean/replace air filter.

 

 

 

 

5.

Low oil level/dirty oil.

 

5.

Check oil level/change oil.

 

 

 

 

6.

Faulty spark plug.

 

6.

Clean and regap or change spark plug.

 

 

 

 

7.

Dirty fuel filter.

 

7.

Replace fuel filter.

 

 

 

 

8.

Stale or dirty fuel.

 

8.

Empty fuel tank and refill tank with fresh, clean gasoline.

 

 

 

 

9.

Water in fuel.

 

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

 

 

 

 

gasoline and replace fuel filter.

 

 

 

 

10.

Spark plug wire loose.

 

10.

Connect and tighten spark plug wire.

 

 

 

 

11.

Dirty engine air screen/fins.

 

11.

Clean engine air screen/fins.

 

 

 

 

12.

Dirty/clogged muffler.

 

12.

Clean/replace muffler.

 

 

 

 

13.

Loose or damaged wiring.

 

13.

Check all wiring.

 

 

 

 

14.

Carburetor out of adjustment.

 

14.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

 

 

 

 

section.

 

 

 

 

15.

Engine valves out of adjustment.

 

15.

Contact an authorized service center/department.

 

 

 

 

 

 

 

 

 

 

Excessive vibration

 

1.

Worn, bent or loose blade.

 

1.

Replace blade. Tighten blade bolt.

 

 

 

 

2.

Bent blade mandrel.

 

2.

Replace blade mandrel.

 

 

 

 

3.

Loose/damaged part(s).

 

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model PB195H46YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Unassembled Parts AssemblyTo Remove Tractor from Carton Unpack CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation DHE Know Your TractorStopping HOW to USE Your TractorTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Operate MowerReverse Operation System ROS Before Starting the EngineTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBrake Operation TiresEngine Engine OIL Filter CleaningMuffler Spark PlugsTo Install Mower See -21 Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments Turn nut right Turn nut left To raise mower To lower mower To Level MowerTo Check Brake To Replace Mower Drive Belt See FigTo Replace Motion Drive Belt See Fig Replacing Battery See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Suggested Guide for Sighting Slopes for Safe Operation L5V 3E4 Limited WarrantyService Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Garantie cette de exclus sont normal l’entretien et AutoriséInitiale d’achat date la de compter à jours 90 dix UNE Pliez EST Ceci Degrés Suivant LESCorrection Cause Problème Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Moteur EntreposageTracteur GAZ DES Commande LA DE Câble LE Régler Pour Starter DU Commande LA Régler PourReglages ET Revision MoteurFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Fig la Voir Batterie LA ReplacerAvant Roue LA DE PINCEMENT/CARROSSAGE Fig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour Réglages ET RévisionFreins LES Vérifier Pour 27 .FIG25 .FIG Tondeuse LA Niveau LE Ajuster Pour24 .FIG 23 .FIG20 .FIG 21 .FIG 19 .FIG18 .FIG Coin le Soulevez C Arrières Bielles LES AttachezFig Voir Courroie LA ET Tondeuse LA InstallerTondeuse LA Enlever Pour 17 .FIGFig la Voir Entretien’ALLUMAGE Bougie Moteur DE D’HUILE Filtre’AIR Tamis LE Nettoyer AIR À FiltreSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverGénérales Recommandations LESLubrification DE Tableau Utilisation Chaque AvantTondre DE Conseils Utilisation12 .FIG Moteur LE Démarrer Pour Transmission LA PurgerQuetimaauto Sion Transmis DE Réchauffement11 et 3 .Fig les Voir Moteur LE Démarrer DE AvantMAR EN Fonctionnement DE Système Jauge DE Roues LES Régler Pour Tondeuse LA Utiliser Pour10 .FIG Système DU CaractéristiquesVitess GAZ DES Commande LA Utiliser PourDE Régulateur LE Utiliser Comment Fig la Voir Mentnetionsta DE Frein LE Engager PourUtilisation ’EMBRAYAGE Desmancom des tionfonc la et MontageLA DE Tracteur LE Retirer Pour Toncar DU Tracteur LE Sortir Pour Montées NON PiécesFig la Voir Batterie LA Vérifier Fig la Voir Siège LE AjustezClient DU Responsabilités SommaireProduit DE Spécifications Remorquage EntretienEnfants Général EntretienLES Dans Fonctionnement PentesGénéral Fonctionnement Tracteurs des sécurité toute en l’utilisation pour ConseilsAvertissement AUX Imprimé

417217 specifications

The Poulan 417217 is a robust and versatile chainsaw that caters to both professional and amateur users alike. Known for its reliability and ease of use, the Poulan 417217 has gained a reputation in the market as an efficient tool for various cutting tasks, from trimming trees to felling larger timber.

At the heart of the Poulan 417217 is its powerful engine, typically featuring a 42cc two-stroke engine that provides a balance between power and efficiency. This engine delivers a sufficient horsepower output to tackle demanding jobs while maintaining manageable weight for user comfort. The advanced engine design also ensures reduced emissions, making it an environmentally-friendly option for users concerned about their carbon footprint.

One of the standout features of the Poulan 417217 is its ease of starting. The chainsaw is equipped with an automatic oiler system that keeps the chain lubricated during use, prolonging its lifespan and maintaining optimal performance. The quick-release air filter system allows for simple maintenance and easy access when cleaning, which is crucial for the longevity and reliability of the tool.

The chainsaw's 18-inch cutting bar is designed for efficient cutting and maneuverability. It makes quick work of branches and logs, providing smooth performance on various materials. Coupled with a low-kickback chain, safety becomes a priority, helping to prevent accidents during operation.

Ergonomically designed handles enhance user comfort and control, minimizing fatigue during extended periods of use. The vibration dampening technology integrated into the handle design further contributes to an enjoyable user experience by reducing vibrations that can lead to hand fatigue.

The Poulan 417217 also features a combination of a primer bulb and a choke for quick and easy starting, allowing the user to begin their task with minimal delay. Additionally, the chainsaw's lightweight design allows for easy transport and prolonged use without excessive strain.

In summary, the Poulan 417217 offers a combination of power, safety, and user-friendly features, making it an ideal choice for anyone seeking a dependable chainsaw. Whether you are a seasoned professional or a novice, the 417217 equips you with the performance needed to achieve your cutting goals efficiently and safely.
Top Page Image Contents