Poulan 190944 owner manual Tractor

Page 16

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 13)

Raise mower to highest position to allow access to blades.

Remove blade bolt, lock washer and flat washer se- curing blade.

Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Reassemble blade bolt, lock washer and flat washer in exact order as shown.

Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS HEATTREATED.IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVE BOLT SHOWN IN THE REPAIR PARTS.

TRAILING

 

 

MANDREL

EDGE UP

 

2

ASSEMBLY

BLADE

 

4

 

1

1

 

 

 

 

0

 

 

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE BOLT

FIG. 13

TO SHARPEN BLADE (See Fig. 14)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

01202

BLADE

 

 

OR PIN

FIG. 14

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause

16the battery to “leak” power.

Image 16
Contents PD185H42STB Always Wear EYE Protection During OperationIV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigTo Convert to Bagging or Discharging Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate Mower See FigTo Transport See Figs Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsMaintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Check and Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points When operator leaves seat Schematic Tractor - Model Number PD185H42ST PD185H42STBElectrical KEY Part Description Chassis KEY Drive 178122 Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck 152182032X421 Service Notes Service Notes Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

190944 specifications

The Poulan 190944 is a high-performance chainsaw designed for both professional and residential use. It combines power, efficiency, and user-friendly features to meet a variety of cutting needs, from felling trees to pruning branches. Crafted with practicality in mind, this chainsaw boasts an array of technologies and characteristics that make it stand out in the competitive market.

One of the main features of the Poulan 190944 is its robust engine. It typically features a 42cc engine, providing ample power for demanding cutting tasks while still maintaining an efficient fuel consumption rate. This balance allows users to enjoy extended cutting sessions without frequent refueling, making it ideal for larger projects.

Safety is a paramount consideration in the design of the Poulan 190944. The chainsaw is equipped with several safety features, including a chain brake that engages automatically in the event of a kickback, helping to protect the user from potential injuries. Additionally, it incorporates a low-vibration design, which minimizes operator fatigue during extended use.

The Poulan 190944 also offers an easy-start system, ensuring reliable ignition with minimal effort. This is particularly beneficial for users who may not have extensive experience with chainsaws, as it allows them to get started quickly and effortlessly. Furthermore, the tool-less chain tensioning feature allows users to adjust the chain tension without the need for additional tools, making maintenance straightforward and convenient.

Another important characteristic of the Poulan 190944 is its lightweight design. Weighing in at around 10-12 pounds, it is relatively easy to maneuver, enabling users to operate it effectively even in tight spaces. The ergonomic handle design promotes a comfortable grip, reducing strain on the hands and arms during prolonged use.

In terms of performance, the Poulan 190944 features a 16-inch bar and chain, which strikes a balance between cutting capacity and ease of handling. This length is versatile enough to tackle small to medium-sized trees and limbs while still being manageable for detailed work.

Overall, the Poulan 190944 is a reliable and efficient chainsaw that caters to a wide range of users. With its powerful engine, safety features, easy maintenance, and comfortable design, it provides a dependable option for anyone looking to handle outdoor cutting tasks with confidence.