Poulan 190944 To Convert to Bagging or Discharging, Check Tire Pressure, Check Deck Levelness

Page 8

ASSEMBLY

RETAINER

SPRING

PIN

SHOULDER

BOLT

ADJUSTING

BAR

GAUGE

 

 

WHEEL

3/8 WASHER

3/8-16 CENTER

 

LOCKNUT

 

 

FIG. 4

INSTALL MULCHER PLATE (See Fig. 5) (If previously removed)

•Raise and hold deflector shield in upright position.

•Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

•Hook front latch into hole on front of mower deck.

•Hook rear latch into hole on back of mower deck.

CAUTION: Do not remove deflector shield from mower.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change blades. The mulcher blades are designed for discharging and bagging also.

DEFLECTOR

SHIELD

MULCHER

PLATE

LATCH

HOOKS

FIG. 5

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

•Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER HOUSING”in the Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual.

✓CHECKLIST

BEFOREYOU OPERATE AND ENJOYYOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROMTHIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

✓All assembly instructions have been completed.

✓No remaining loose parts in carton.

✓Battery is properly prepared and charged. (Minimum 1 hour at 6 amps).

✓Seat is adjusted comfortably and tightened securely.

✓All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

✓Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

✓Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓Check wiring. See that all connections are still secure and wires are properly clamped.

✓Before driving tractor, be sure freewheel control is in drive position.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓Engine oil is at proper level.

✓Fuel tank is filled with fresh, clean, regular unleaded gasoline.

✓Become familiar with all controls - their location and function. Operate them before you start the engine.

✓Be sure brake system is in safe operating condition.

✓It is important to purge the transmission before oper- ating your tractor for the first time. Follow proper start- ing and transmission purging instructions (See “TO

START ENGINE” and “PURGE TRANSMISSION” in

8the Operation section of this manual).

Page 7 Page 9
Image 8
Page 7 Page 9
Contents PD185H42STB Always Wear EYE Protection During OperationIV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigTo Convert to Bagging or Discharging Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsMaintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Check and Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points When operator leaves seat Schematic Tractor - Model Number PD185H42ST PD185H42STBElectrical KEY Part Description Chassis KEY Drive 178122 Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck 152182032X421 Service Notes Service Notes Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

190944 specifications

The Poulan 190944 is a high-performance chainsaw designed for both professional and residential use. It combines power, efficiency, and user-friendly features to meet a variety of cutting needs, from felling trees to pruning branches. Crafted with practicality in mind, this chainsaw boasts an array of technologies and characteristics that make it stand out in the competitive market.

One of the main features of the Poulan 190944 is its robust engine. It typically features a 42cc engine, providing ample power for demanding cutting tasks while still maintaining an efficient fuel consumption rate. This balance allows users to enjoy extended cutting sessions without frequent refueling, making it ideal for larger projects.

Safety is a paramount consideration in the design of the Poulan 190944. The chainsaw is equipped with several safety features, including a chain brake that engages automatically in the event of a kickback, helping to protect the user from potential injuries. Additionally, it incorporates a low-vibration design, which minimizes operator fatigue during extended use.

The Poulan 190944 also offers an easy-start system, ensuring reliable ignition with minimal effort. This is particularly beneficial for users who may not have extensive experience with chainsaws, as it allows them to get started quickly and effortlessly. Furthermore, the tool-less chain tensioning feature allows users to adjust the chain tension without the need for additional tools, making maintenance straightforward and convenient.

Another important characteristic of the Poulan 190944 is its lightweight design. Weighing in at around 10-12 pounds, it is relatively easy to maneuver, enabling users to operate it effectively even in tight spaces. The ergonomic handle design promotes a comfortable grip, reducing strain on the hands and arms during prolonged use.

In terms of performance, the Poulan 190944 features a 16-inch bar and chain, which strikes a balance between cutting capacity and ease of handling. This length is versatile enough to tackle small to medium-sized trees and limbs while still being manageable for detailed work.

Overall, the Poulan 190944 is a reliable and efficient chainsaw that caters to a wide range of users. With its powerful engine, safety features, easy maintenance, and comfortable design, it provides a dependable option for anyone looking to handle outdoor cutting tasks with confidence.
Top Page Image Contents