Poulan 190944 owner manual To Replace Motion Drive Belt See Fig, To Check Brake, To Adjust Brake

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

 

NUT “A”

 

1-9/16"

OPERATING

JAM NUT

 

ARM

 

BELT INSTALLATION -

•Carefully work new belt down onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

FIG. 25

02557-LTH

FIG. 24

TO REPLACE MOTION DRIVE BELT (See Fig. 25)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

• Remove belt from stationary idler and clutching idler.

 

• Remove belt downward from around engine pulley.

 

• Pull belt slack toward rear of tractor. Carefully remove

 

belt upwards from transmission input pulley.

 

• Remove belt from center span keeper and pull belt

21

away from tractor.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation PD185H42STBSafe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigCheck Tire Pressure To Convert to Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Operate on HillsTo Transport See Figs Check Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsLubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points When operator leaves seat Tractor - Model Number PD185H42ST PD185H42STB SchematicElectrical KEY Part Description Chassis KEY Drive 178122 Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineMower Lift 152 Mower Deck182032X421 Service Notes Service Notes Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

190944 specifications

The Poulan 190944 is a high-performance chainsaw designed for both professional and residential use. It combines power, efficiency, and user-friendly features to meet a variety of cutting needs, from felling trees to pruning branches. Crafted with practicality in mind, this chainsaw boasts an array of technologies and characteristics that make it stand out in the competitive market.

One of the main features of the Poulan 190944 is its robust engine. It typically features a 42cc engine, providing ample power for demanding cutting tasks while still maintaining an efficient fuel consumption rate. This balance allows users to enjoy extended cutting sessions without frequent refueling, making it ideal for larger projects.

Safety is a paramount consideration in the design of the Poulan 190944. The chainsaw is equipped with several safety features, including a chain brake that engages automatically in the event of a kickback, helping to protect the user from potential injuries. Additionally, it incorporates a low-vibration design, which minimizes operator fatigue during extended use.

The Poulan 190944 also offers an easy-start system, ensuring reliable ignition with minimal effort. This is particularly beneficial for users who may not have extensive experience with chainsaws, as it allows them to get started quickly and effortlessly. Furthermore, the tool-less chain tensioning feature allows users to adjust the chain tension without the need for additional tools, making maintenance straightforward and convenient.

Another important characteristic of the Poulan 190944 is its lightweight design. Weighing in at around 10-12 pounds, it is relatively easy to maneuver, enabling users to operate it effectively even in tight spaces. The ergonomic handle design promotes a comfortable grip, reducing strain on the hands and arms during prolonged use.

In terms of performance, the Poulan 190944 features a 16-inch bar and chain, which strikes a balance between cutting capacity and ease of handling. This length is versatile enough to tackle small to medium-sized trees and limbs while still being manageable for detailed work.

Overall, the Poulan 190944 is a reliable and efficient chainsaw that caters to a wide range of users. With its powerful engine, safety features, easy maintenance, and comfortable design, it provides a dependable option for anyone looking to handle outdoor cutting tasks with confidence.
Top Page Image Contents