Poulan 190944 Tools Required for Assembly, To Remove Tractor from CAR- TON, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

1/2 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

 

STEERING

 

BOOT

 

TABS

ADAPTER

EXTENSION SHAFT

 

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER STEERING SHAFT

TAB SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PD185H42STB Always Wear EYE Protection During OperationGeneral Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationSafety Rules Table of Contents Unassembled Parts To Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See FigCheck Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Operate on HillsTo Transport See Figs ADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsGeneral Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Check BrakeReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points When operator leaves seat Schematic Tractor - Model Number PD185H42ST PD185H42STBElectrical KEY Part Description Chassis KEY Drive 178122 Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentMower Lift Mower Deck 152182032X421 Service Notes Service Notes Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

190944 specifications

The Poulan 190944 is a high-performance chainsaw designed for both professional and residential use. It combines power, efficiency, and user-friendly features to meet a variety of cutting needs, from felling trees to pruning branches. Crafted with practicality in mind, this chainsaw boasts an array of technologies and characteristics that make it stand out in the competitive market.

One of the main features of the Poulan 190944 is its robust engine. It typically features a 42cc engine, providing ample power for demanding cutting tasks while still maintaining an efficient fuel consumption rate. This balance allows users to enjoy extended cutting sessions without frequent refueling, making it ideal for larger projects.

Safety is a paramount consideration in the design of the Poulan 190944. The chainsaw is equipped with several safety features, including a chain brake that engages automatically in the event of a kickback, helping to protect the user from potential injuries. Additionally, it incorporates a low-vibration design, which minimizes operator fatigue during extended use.

The Poulan 190944 also offers an easy-start system, ensuring reliable ignition with minimal effort. This is particularly beneficial for users who may not have extensive experience with chainsaws, as it allows them to get started quickly and effortlessly. Furthermore, the tool-less chain tensioning feature allows users to adjust the chain tension without the need for additional tools, making maintenance straightforward and convenient.

Another important characteristic of the Poulan 190944 is its lightweight design. Weighing in at around 10-12 pounds, it is relatively easy to maneuver, enabling users to operate it effectively even in tight spaces. The ergonomic handle design promotes a comfortable grip, reducing strain on the hands and arms during prolonged use.

In terms of performance, the Poulan 190944 features a 16-inch bar and chain, which strikes a balance between cutting capacity and ease of handling. This length is versatile enough to tackle small to medium-sized trees and limbs while still being manageable for detailed work.

Overall, the Poulan 190944 is a reliable and efficient chainsaw that caters to a wide range of users. With its powerful engine, safety features, easy maintenance, and comfortable design, it provides a dependable option for anyone looking to handle outdoor cutting tasks with confidence.
Top Page Image Contents