Poulan 190944 owner manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 29

TERMINAL

KEPS

NUT

COVER

 

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

FIG. 30

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02778

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation PD185H42STBII. Slope Operation IV. ServiceSafe Operation Practices for Ride-On Mowers General OperationSafety Rules Table of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CAR- TONAssemble Gauge Wheels to Mower Deck See Fig Check Battery See FigCheck for Proper Position of ALL Belts To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Operate Mower See FigTo Operate on Hills To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMulching Mowing Tips Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal To Check and Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Replacing Battery See FigsTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points When operator leaves seat Tractor - Model Number PD185H42ST PD185H42STB SchematicElectrical KEY Part Description Chassis KEY Drive 178122 Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineMower Lift 152 Mower Deck182032X421 Service Notes Service Notes Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

190944 specifications

The Poulan 190944 is a high-performance chainsaw designed for both professional and residential use. It combines power, efficiency, and user-friendly features to meet a variety of cutting needs, from felling trees to pruning branches. Crafted with practicality in mind, this chainsaw boasts an array of technologies and characteristics that make it stand out in the competitive market.

One of the main features of the Poulan 190944 is its robust engine. It typically features a 42cc engine, providing ample power for demanding cutting tasks while still maintaining an efficient fuel consumption rate. This balance allows users to enjoy extended cutting sessions without frequent refueling, making it ideal for larger projects.

Safety is a paramount consideration in the design of the Poulan 190944. The chainsaw is equipped with several safety features, including a chain brake that engages automatically in the event of a kickback, helping to protect the user from potential injuries. Additionally, it incorporates a low-vibration design, which minimizes operator fatigue during extended use.

The Poulan 190944 also offers an easy-start system, ensuring reliable ignition with minimal effort. This is particularly beneficial for users who may not have extensive experience with chainsaws, as it allows them to get started quickly and effortlessly. Furthermore, the tool-less chain tensioning feature allows users to adjust the chain tension without the need for additional tools, making maintenance straightforward and convenient.

Another important characteristic of the Poulan 190944 is its lightweight design. Weighing in at around 10-12 pounds, it is relatively easy to maneuver, enabling users to operate it effectively even in tight spaces. The ergonomic handle design promotes a comfortable grip, reducing strain on the hands and arms during prolonged use.

In terms of performance, the Poulan 190944 features a 16-inch bar and chain, which strikes a balance between cutting capacity and ease of handling. This length is versatile enough to tackle small to medium-sized trees and limbs while still being manageable for detailed work.

Overall, the Poulan 190944 is a reliable and efficient chainsaw that caters to a wide range of users. With its powerful engine, safety features, easy maintenance, and comfortable design, it provides a dependable option for anyone looking to handle outdoor cutting tasks with confidence.
Top Page Image Contents