Poulan 191641 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 8

ASSEMBLY/PRE-OPERATION

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below.

(1)

3/4" wrench

(1)

Pliers

(2)

7/16" wrench

(1)

Utility knife

(1)

Tire pressure gauge

 

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

1.Remove locknut and large flat washer from steering shaft.

2.Position front wheels of the tractor so they are pointing straight forward.

3.Slide the steering sleeve over the steering shaft.

4.Align tabs and press steering sleeve extension into bottom of steering wheel.

5.Position steering wheel so cross bars are horizontal (left to right) and slide onto steering wheel adapter.

6.Secure steering wheel to steering shaft with locknut and large flat washer previously removed. Tighten securely.

7.Snap steering wheel insert into center of steering wheel.

8.Remove protective materials from trac-

tor hood and grill.

IMPORTANT: Check for and remove any staples in skid that may puncture tires where tractor is to roll off skid.

 

Steering Wheel

 

Insert

 

Lock Nut

 

Large Flat

 

Washer

Steering Wheel

 

 

Steering

 

Wheel

Steering

Adaptor

Wheel Extention

Tabs

Steering

Shaft

Steering

Sleeve

02143

CHECK BATTERY

1. Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc- tions).

Label

02173

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

8

Image 8
Contents Model NO. CO185H42STA Table of Contents WarrantyII. Slope Operation Safety RulesGeneral Operation Do not IV. ServiceIII. Children Safety Rules API-SG-SL Product SpecificationsCustomer Responsibilities Unassembled Parts Before Removing Tractor from Skid Tools Required for AssemblyTo Remove Tractor from Carton Install Mulcher Plate If previously removed Checklist To Convert to Bagging or DischargingReposition Right Rear Gauge Wheel Check Tire PressureOperation Know Your Tractor HOW to USE Your Tractor To Transport To Operate MowerTo Operate on Hills Before Starting the Engine To Start EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsMulching Mowing Tips Before Each USE MaintenanceGeneral Recommendations Tractor Engine Service and Adjustments CleaningTo Install Mower To Level Mower HousingSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentTo Replace Motion Drive Belt To Check and Adjust BrakeTo Replace Mower Blade Drive Belt Transaxle Motion Control LE- VER Neutral Adjustment To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Battery OtherFuel System Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation