Poulan 180200 owner manual Tractor

Page 18

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjust- ments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PROD- UCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

BLADEMANDREL

ASSEMBLY

CENTER

HOLE

BLADE BOLT (SPECIAL)

STAR

FIG. 13

I M P O R T A N T : TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

CENTER HOLE

BLADE

5/8" BOLT OR PIN

FIG. 14

TO SHARPEN BLADE (See Fig. 14)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not neces- sary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the

18 SERVICE AND ADJUSTMENTS section of this manual).

Page 17 Page 19
Image 18
Page 17 Page 19
Contents DPR22H48STB Safety Rules Safe Operation Practices for Ride-On MowersSafety Rules Table of Contents Unassembled Parts HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigPurge Transmission Mowing TipsGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Engine Spark Plugs CleaningMuffler Engine OIL FilterTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive BeltTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigTo Remove Hood and Grill Assembly See Fig Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Service Notes Schematic Tractor Model Number DPR22H48STCElectrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Transaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip Engine Optional EquipmentSeat Assembly Decals Wheels & TiresMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

180200 specifications

The Poulan 180200 is a powerful and efficient chainsaw that caters to a variety of cutting tasks, making it an ideal choice for both residential users and professionals alike. Known for its reliability and performance, the Poulan 180200 harnesses advanced technology to deliver the features that woodworkers, gardeners, and landscapers need.

At the heart of the Poulan 180200 is its robust 18-inch bar and chain, specifically designed for optimal cutting performance. This length strikes a balance between agility and the ability to tackle larger limbs and tree trunks with ease. The chainsaw is powered by a dependable 42cc two-cycle engine, providing sufficient power to handle demanding cutting tasks while ensuring smooth operation.

One of the key features of the Poulan 180200 is its Easy Start system. This innovative technology significantly reduces the effort needed to start the chainsaw, allowing users to get to work quickly and efficiently. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that draws fuel into the carburetor, further enhancing the starting process.

Safety is a priority with the Poulan 180200. The chainsaw includes several safety features, such as a chain brake that automatically stops the chain in the event of kickback. This feature is crucial for preventing accidents and ensuring user safety during operation. The anti-vibration system also provides a more comfortable cutting experience by reducing the effects of chain vibrations, making it easier to handle for extended periods.

Durability is another characteristic that defines the Poulan 180200. The chainsaw features a metal bumper spike that helps to provide better control and stability during cutting tasks. The high-quality design also ensures longevity, allowing users to rely on the chainsaw for years to come.

In terms of maintenance, the Poulan 180200 is user-friendly. The easy-access air filter and tool-less chain tensioning system make it simple to maintain and adjust the chainsaw for consistent performance. These features cater to users who wish to spend less time on upkeep and more time on their cutting projects.

In summary, the Poulan 180200 is a well-rounded chainsaw that brings together power, efficiency, and safety. With its reliable performance, user-friendly features, and robust design, it is a dependable tool for anyone looking to tackle a range of cutting tasks, whether in the yard or the forest.
Top Page Image Contents