Poulan 180200 owner manual Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 21

SERVICE AND ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key “OFF” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 19)

•Place attachment clutch in “DISENGAGED” position.

•If equipped, turn height adjustment knob to lowest setting.

•Lower mower to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove retainer spring holding anti-swaybar to chassis bracket and disengage anti-swaybar from bracket.

•Remove four retainer springs from front plate assembly and remove plate.

•Remove retainer springs from suspension arms at deck and disengage arms from deck.

•Raise attachment lift to its highest position.

•Slide mower forward and remove belt from electric clutch pulley.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Follow procedure described in “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual.

BELT TENSION ROD

SUSPENSION ARMS

 

(DISENGAGED

 

POSITION)

 

CHASSIS

BRACKET

RETAINER

SPRING

ANTI-SWAY

BAR

RETAINER

SPRINGS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 20

FRONT

MOWER ELECTRIC

BRACKET CLUTCH PULLEY

FRONT

PLATE ASSEMBLY

RETAINER

SPRINGS (BOTH SIDES)

FRONT

MOWER

BRACKET

FIG. 19

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents DPR22H48STB Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigTo Adjust Carburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor Model Number DPR22H48STC SchematicElectrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Transaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip Optional Equipment EngineSeat Assembly Wheels & Tires DecalsMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

180200 specifications

The Poulan 180200 is a powerful and efficient chainsaw that caters to a variety of cutting tasks, making it an ideal choice for both residential users and professionals alike. Known for its reliability and performance, the Poulan 180200 harnesses advanced technology to deliver the features that woodworkers, gardeners, and landscapers need.

At the heart of the Poulan 180200 is its robust 18-inch bar and chain, specifically designed for optimal cutting performance. This length strikes a balance between agility and the ability to tackle larger limbs and tree trunks with ease. The chainsaw is powered by a dependable 42cc two-cycle engine, providing sufficient power to handle demanding cutting tasks while ensuring smooth operation.

One of the key features of the Poulan 180200 is its Easy Start system. This innovative technology significantly reduces the effort needed to start the chainsaw, allowing users to get to work quickly and efficiently. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that draws fuel into the carburetor, further enhancing the starting process.

Safety is a priority with the Poulan 180200. The chainsaw includes several safety features, such as a chain brake that automatically stops the chain in the event of kickback. This feature is crucial for preventing accidents and ensuring user safety during operation. The anti-vibration system also provides a more comfortable cutting experience by reducing the effects of chain vibrations, making it easier to handle for extended periods.

Durability is another characteristic that defines the Poulan 180200. The chainsaw features a metal bumper spike that helps to provide better control and stability during cutting tasks. The high-quality design also ensures longevity, allowing users to rely on the chainsaw for years to come.

In terms of maintenance, the Poulan 180200 is user-friendly. The easy-access air filter and tool-less chain tensioning system make it simple to maintain and adjust the chainsaw for consistent performance. These features cater to users who wish to spend less time on upkeep and more time on their cutting projects.

In summary, the Poulan 180200 is a well-rounded chainsaw that brings together power, efficiency, and safety. With its reliable performance, user-friendly features, and robust design, it is a dependable tool for anyone looking to tackle a range of cutting tasks, whether in the yard or the forest.
Top Page Image Contents