Poulan 180200 owner manual Off

Page 29

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves

 

 

 

corrected, contact an authorized service center/

seat with attachment

 

 

 

department.

clutch engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Switch is “OFF”.

1.

Turn switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires”

1.

Engine throttle control not set at “SLOW”

1.

Move throttle control to “SLOW” position and allow

when turning engine

 

position for 30 seconds before stopping engine.

 

to idle for 30 seconds before stopping engine.

“OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents DPR22H48STB Safe Operation Practices for Ride-On Mowers Safety RulesSafety Rules Table of Contents Unassembled Parts Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionCustomer Responsibilities Lubrication ChartGeneral Recommendations Before Each USETractor Engine Muffler CleaningSpark Plugs Engine OIL FilterTo Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Hood and Grill Assembly See Fig Replacing Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control Cable See FigTo Adjust Choke Control See Fig Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Service Notes Tractor Model Number DPR22H48STC SchematicElectrical KEY Part Description Chassis and Enclosures Bracket Fender Drive Transaxle Order parts from Steering Assembly 175118 Bolt Shoulder 7/16-20 Unc 175553 Clip Optional Equipment EngineSeat Assembly Wheels & Tires DecalsMower Lift Mower Deck Washer, Spacer Mower Vented Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

180200 specifications

The Poulan 180200 is a powerful and efficient chainsaw that caters to a variety of cutting tasks, making it an ideal choice for both residential users and professionals alike. Known for its reliability and performance, the Poulan 180200 harnesses advanced technology to deliver the features that woodworkers, gardeners, and landscapers need.

At the heart of the Poulan 180200 is its robust 18-inch bar and chain, specifically designed for optimal cutting performance. This length strikes a balance between agility and the ability to tackle larger limbs and tree trunks with ease. The chainsaw is powered by a dependable 42cc two-cycle engine, providing sufficient power to handle demanding cutting tasks while ensuring smooth operation.

One of the key features of the Poulan 180200 is its Easy Start system. This innovative technology significantly reduces the effort needed to start the chainsaw, allowing users to get to work quickly and efficiently. This feature is especially beneficial for those who may struggle with traditional pull-start mechanisms. Additionally, the chainsaw is equipped with a primer bulb that draws fuel into the carburetor, further enhancing the starting process.

Safety is a priority with the Poulan 180200. The chainsaw includes several safety features, such as a chain brake that automatically stops the chain in the event of kickback. This feature is crucial for preventing accidents and ensuring user safety during operation. The anti-vibration system also provides a more comfortable cutting experience by reducing the effects of chain vibrations, making it easier to handle for extended periods.

Durability is another characteristic that defines the Poulan 180200. The chainsaw features a metal bumper spike that helps to provide better control and stability during cutting tasks. The high-quality design also ensures longevity, allowing users to rely on the chainsaw for years to come.

In terms of maintenance, the Poulan 180200 is user-friendly. The easy-access air filter and tool-less chain tensioning system make it simple to maintain and adjust the chainsaw for consistent performance. These features cater to users who wish to spend less time on upkeep and more time on their cutting projects.

In summary, the Poulan 180200 is a well-rounded chainsaw that brings together power, efficiency, and safety. With its reliable performance, user-friendly features, and robust design, it is a dependable tool for anyone looking to tackle a range of cutting tasks, whether in the yard or the forest.
Top Page Image Contents