Poulan SP24H48YT manual To Level Mower Housing, SIDE-TO-SIDE Adjustment

Page 25

9.Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brack- ets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: Check belt for proper rout- ing in all mower pulley grooves.

10.Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and en- gage slowly.

11.Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

12.If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

13.Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

• Recheck measurements after adjusting.

Bottom Edge of

Bottom Edge of

Mower to Ground

Mower to Ground

00598

 

Suspension

Arm

01553

Lift Link

Adjustment Nut

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side- to-side. If the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of blade

•Before making any necessary adjust- ments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

Blade

02548

A

GROUND LINE

A

“B”“B”

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Operators Manual Warranty Table of ContentsGeneral Operation Safety RulesII. Slope Operation Service Safe Handling of GasolineIII. Children IV. TowingGeneral Service Customer Responsibilities Product SpecificationsAPI-SG-SL Gauge Wheels Nose Roller Unassembled PartsTools Required for Assembly ASSEMBLY/PRE-OPERATIONTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat Assemble Gauge Wheels to Mower Deck To Attach Nose RollerInstall Mower and Drive Belt Check Tire Pressure ChecklistCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Choke Control HOW to USE Your TractorTo Adjust Gauge Wheels To Adjust Mower Cutting HeightTo Operate Mower Reverse Operation System ROSTo Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsADD Gasoline To Start EnginePurge Transmission Mowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine AIR Filter CleaningTo Install Mower Service and AdjustmentsTo Remove Mower SIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Drive Belt Mower Drive Belt InstallationMower Drive Belt Removal To Replace Mower Blade SEC- Ondary Drive Belt Install NEW Mower Blade Secondary Drive BeltRemove Mower Drive Belt Remove Mower Blade Secondary Drive BeltTo Adjust Brake To Check and Adjust BrakeBelt Installation To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transmission Removal ReplacementFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Throttle Control Cable Replacing BatteryTo Adjust Carburetor To Replace Headlight BulbStorage BatteryOther Problem Cause Correction Troubleshooting ChartExcessive Poor grass Suggested Guide for Sighting Slopes for Safe Operation

SP24H48YT specifications

The Poulan SP24H48YT is a powerful and versatile lawn tractor designed to meet the needs of homeowners and gardeners who seek an efficient and reliable machine for maintaining their landscapes. With its robust build and user-friendly features, this model aims to simplify lawn care while delivering exceptional performance.

One of the standout features of the Poulan SP24H48YT is its 24 HP Briggs & Stratton engine. This engine provides ample power for cutting through thick grass and tackling tough terrains. The auto transmission allows for smooth and effortless operation, enabling users to “set it and forget it” when it comes to handling different terrains while ensuring a consistent and even cut.

The 48-inch cutting deck is made from high-quality materials, ensuring durability and longevity. The deck is equipped with a mulching capability, which allows grass clippings to be finely cut and returned to the lawn, promoting healthier growth. Users can also adjust the cutting height with ease, offering a range of height settings to achieve the precise look and feel desired for their lawns.

For added convenience, the Poulan SP24H48YT features an easy-to-use dashboard with controls that are intuitive and ergonomic. The steering wheel is designed for comfort, reducing fatigue during long mowing sessions. The high-back seat also adds to the overall comfort, allowing operators to mow for extended periods without discomfort.

This model is built with user-centric technologies such as LED headlights, ensuring visibility during early morning or late evening mowing sessions. Additionally, the reinforced frame and wheels enhance stability and maneuverability, making it easy to navigate around flower beds and obstacles in the yard.

Maintenance is also simplified, as the Poulan SP24H48YT includes an easily accessible oil drain and an air filter that is simple to clean or replace. The machine’s rugged construction is designed to withstand the rigors of regular use, promising years of dependable service.

In summary, the Poulan SP24H48YT lawn tractor combines power, precision, and ease of use in a single package. Its advanced engine, adjustable cutting deck, comfortable design, and thoughtful features make it an excellent choice for homeowners looking to achieve a manicured lawn with minimal effort. Whether for routine mowing or more extensive landscaping tasks, this lawn tractor stands out as a reliable companion in outdoor maintenance.
Top Page Image Contents