Poulan PP4620AVHD Cutting Methods, Starting a Warm Engine, Chain Brake, Important Points

Page 10

4.Push the choke/fast idle lever in to the HALF CHOKE position.

5.Pull the starter rope quickly with your right hand until the engine starts.

6.Allow the engine to run for approximately 30 seconds. Then, squeeze and release throttle trigger to allow engine to return to idle speed.

ON/STOP SWITCH

CHOKE/FAST IDLE LEVER

FULL HALF OFF

(0.5 mm) thick. Repairs on a chain brake should be made by an authorized service deal- er. Take your unit to the place of purchase if purchased from a servicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON position.

2.Pull the choke/fast idle lever out to the HALF CHOKE position.

3.Pull the starter rope quickly with your right hand until the engine starts.

4.Squeeze and release the throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded if it has not started after 10 pulls.

Flooded engines can be cleared of excess fuel by following the warm engine starting proce- dure listed above. Ensure the ON/STOP switch is in the ON position.

Starting could require many pulls depending on how badly unit is flooded. If engine still fails to start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0.020″

Braking function control

CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this procedure. This is the only instance when the saw should be placed on the ground with the engine run- ning.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

CUTTING METHODS

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re-

place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and thus increase the possibility of kickback.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PP4620AVHD Starting Reminder Plan AheadHandle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackDo not cut more than one log at a time Maintain ControlReduce the Chance of Kickback Your left arm straight with the elbow lockedChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Attaching the Bumper Spike AssemblyComputed kickback angle CKA Table Attaching the BAR & Chain If notTip Bar Adjusting the tensionInside view Chain Brake Adjustment located on Chain Brake CuttersOperation Fueling Engine Fueling & LubricationStarting BAR and Chain LubricationChain Brake Cutting MethodsStarting a Warm Engine Important PointsFelling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Types of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Without a SupportPruning Limbing and Pruning Important PointsLimbing ErlyCleaning the Spark Arresting Screen ServiceCleaning the air filter AIR FilterStorage Need ASSISTANCE? Troubleshooting TableNeed Service PART? Trouble Cause RemedyLigations The U. S. Environmental Limited WarrantyElectrolux Home PRODUCTS, INC NANCE, Replacement and Repair of Emission Related Parts Any

PP4620AVHD specifications

The Poulan PP4620AVHD is a robust chainsaw engineered for homeowners and occasional users seeking a blend of performance, efficiency, and ease of use. This model is particularly well-suited for tackling medium to heavy-duty cutting tasks, such as tree trimming, firewood cutting, and storm cleanup.

One of the standout features of the PP4620AVHD is its powerful 46cc, 2-cycle engine. This engine delivers a strong performance and ensures efficient cutting through a variety of materials. With a top speed of approximately 9,000 RPM, users can expect swift cuts, making short work of logs and branches.

The ease of starting is a crucial aspect of the PP4620AVHD. It incorporates an advanced starting system with a spring-assist mechanism, reducing the effort needed to start the chainsaw. This feature is particularly appreciated during cold starts, allowing the user to spend less time struggling and more time cutting.

The chainsaw is equipped with an 18-inch bar and chain which strikes a balance between maneuverability and cutting capacity. This size is ideal for tackling larger logs while still being manageable for less experienced users. The chain is designed for quick and easy adjustments, ensuring that the user can maintain optimal tension without the need for additional tools.

Safety is a priority in any power tool, and the PP4620AVHD includes multiple safety features. It has a front hand guard to protect the user's hands from flying debris, and a chain brake that engages automatically during kickback situations. These features help ensure a safer cutting experience.

An additional characteristic of the PP4620AVHD is its AV technology (Anti-Vibration). This reduces vibrations felt by the user, which is crucial for extended use, minimizing fatigue and promoting comfort during operation.

For maintenance, the chainsaw has an easy-access air filter and fuel cap, allowing for straightforward cleaning and refueling. Regular maintenance is vital to prolong the life of any chainsaw, and Poulan's design supports user-friendliness in this regard.

The Poulan PP4620AVHD stands out as a capable and versatile chainsaw, perfect for those who need reliable performance without the complexity of professional-grade equipment. It combines power, safety, and comfort, making it a smart choice for both novice and seasoned users looking for an effective cutting tool.
Top Page Image Contents