Adjusting the Speaker Volume Level
This unit is set to the standard level before shipping from the factory. You may not need adjustment.
But, depending on the size of the room and the placement of the speakers, you may need a fine adjustment.
In this case, follow the steps below. Please use the remote control at the listening point.
1.Press [SOURCE] to select the desired function.
2.Press [SURROUND] repeatedly to select the desired surround mode (“DOLBY PL”, “DOLBY 3”, “THEATER” or “HALL”). (See “Selecting the Surround Mode” on Page E16.)
3.Press [TEST TONE] on the remote control. “TTONE” appears and “FL” blinks.
The test tone will be heard from each speaker sequentially as follows.
Surround mode | FL display (Speaker) |
|
|
DOLBY PL | FL (Front left speaker) |
THEATHER | C (Center speaker) |
HALL | FR (Front right speaker) |
| RS (Surround right speaker) |
| LS (Surround left speaker) |
|
|
DOLBY 3 | FL (Front left speaker) |
| C (Center speaker) |
| FR (Front right speaker) |
|
|
b |
|
|
|
|
| E T | P |
| M |
|
|
|
|
|
|
|
| a | |||
|
|
|
|
| U |
|
|
| U |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| E |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| N |
|
|
|
|
|
|
|
|
|
|
|
|
|
| S |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TRIM |
SHIFT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CLEAR | |||||
SHIFT |
|
|
|
|
|
|
|
|
| ENTER |
|
|
|
|
|
|
|
|
|
| ENTER |
|
|
| T |
|
|
|
|
|
|
|
|
|
|
| TRIM | ||||||
| REV |
|
|
| P |
|
|
|
|
|
| L | E |
|
| FWD |
|
| |||
|
|
|
| O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| SLOW |
|
|
| M |
|
|
|
| IT |
|
|
|
| SLOW |
|
| ||||
|
|
|
|
|
| E |
|
|
| B |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| N | U |
| U |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| S |
|
|
|
|
|
|
|
|
|
| |
- |
| P |
|
|
|
|
|
|
|
|
|
|
|
| T |
|
|
| + |
| |
T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
U |
| R |
|
|
|
|
|
|
|
|
|
| X |
|
| E |
| ||||
|
| E |
|
|
|
|
|
|
| E |
|
| N |
|
| ||||||
| NE |
|
|
| V |
| P |
|
|
|
| N |
|
| U |
|
|
| |||
|
|
|
|
|
|
| AUS |
|
|
|
|
|
| T |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| E/STEP |
|
|
|
|
|
|
|
|
|
|
|
1 2 3
ANGLE A.REPLAY ZOOM
4 5 6
AUDIO SLEEP
| 7 | 8 | 9 |
|
| TIMER | ADJUST | SET/CLEAR |
|
| 0 |
| +10 |
|
| CLOCK |
|
|
|
| TU/BAND |
| SOURCE | 1 |
|
|
|
| |
| PRESET | FM MODE | TEST TONE | 3, 5 |
|
|
|
| |
2 | SURROUND | BASS | SOUND | TEST TONE |
|
|
| ||
SURROUND | MUTE | VOLUME |
| |
|
|
|
| |
|
|
|
|
| 4, 6 |
|
|
|
| ||
|
| VOLUME | |||
4.Press [VOLUME] o or p until the test tone is at a comfortable level.
If the test tone level is not the same from each speaker, you may need fine adjustment of the volume level. Please follow the steps as below.
Note:
If no adjustments are made, the original display returns after approximately 15 seconds.
1)Press [TEST TONE] to turn the test tone off.
2)Press [SURROUND] to select the desired surround mode.
3)Press [TRIM] while holding [SHIFT] down. “FNTL 0” appears.
4)Press [ENTER] repeatedly to select the speaker.
FL display (Speaker)
FNTL (Front left speaker)
CENT (Center speaker)
FNTR (Front right speaker)
SURR (Surround right speaker)
SURL (Surround left speaker)
SUBW (Subwoofer)
5)Press [a] or [b] to adjust the volume level. FNTL/FNTR: “0” ~
6)Press [ENTER].
7)Repeat step 4) to 6) for another speaker, if necessary.
8)Press [TRIM] again while holding [SHIFT] down to turn it off.
5.Press [TEST TONE] to turn the test tone off. “TTONE” disappears.
6.Press [VOLUME] o or p to adjust the volume as desired.
Notes:
•There is no Dolby Surround effect when monaural program material is used.
•When receiving weak FM broadcasts, switch the Dolby Pro Logic off. The sound quality may improve.
•When headphones are connected while any of the surround modes are selected, the surround mode is switched off automatically. The SURROUND button does not function while headphones are connected.
•Trimming can be set at each function respectively.