Manual presetting
1.Tune in the station to be preset as described in “Automatic/ Manual Tuning”.
2.Press [c/MEMO]. “PROG.” blinks.
PROG.
MHz
3.While “PROG.” is blinking, press [d/PRESET] (or [PRESET] on the remote control) to select the channel to be preset.
• In this example, the channel is “9”.
PROG.
MHz
4.While “PROG.” is blinking, press [c/MEMO].
•In this example, “103.1 MHz” FM station is preset on FM channel 9.
MHz
5. Repeat steps above to add more preset stations.
•When presetting a new station, the previous preset station is cleared.
POWER/STANDBY |
| FM MODE | VOLUME |
|
| ||
qOPEN/ | a | k | n |
CLOSE | |||
f /TUNE - e /TUNE + d /PRESET | c /MEMO | ||
PHONES |
|
|
|
SURROUND | BASS | SOUND | SOURCE |
3 2, 4
TIMER ADJUST SET/CLEAR
0+10
| CLOCK |
|
|
| TU/BAND |
| FUNCTION |
3 | PRESET | FM MODE | TEST TONE |
|
|
| |
| SURROUND | BASS | SOUND |
| MUTE | - VOLUME + | |
Listening to Preset Stations
1.Press [SOURCE] (or [TU/BAND] on the remote control) to select FM or AM.
2.Press [d/PRESET] (or [PRESET] on the remote control) briefly to select the desired channel.
•The number buttons on the remote control can also be used.
Example: To select No.9, press [0], then [9].
Note: No not press the [+10] button.
Preset scan tuning
1.Press [SOURCE] (or [TU/BAND] on the remote control) to select FM or AM.
2.Press [d/PRESET] (or [PRESET] on the remote control) for at least 1 second.
•The channel number appears.
•The preset stations are selected in sequence for approximately five seconds each.
3.Press [d/PRESET] (or [PRESET] on the remote control) when the desired station has been selected. Preset scanning will stop.
POWER/STANDBY |
| FM MODE | VOLUME |
|
| ||
qOPEN/ | a | k | n |
CLOSE | |||
f /TUNE - e /TUNE + d /PRESET | c /MEMO | ||
PHONES |
|
|
|
SURROUND | BASS | SOUND | SOURCE |
|
|
| 2 1 |
1 | 2 | 3 |
|
ANGLE | A.REPLAY | ZOOM |
|
4 | 5 | 6 | Number |
| AUDIO | SLEEP | |
7 | 8 | 9 | buttons |
TIMER | ADJUST | SET/CLEAR |
0+10
| CLOCK |
|
|
| |
TU/BAND | TU/BAND |
| SOURCE | 1 | |
PRESET | FM MODE | TEST TONE | |||
2 |
| ||||
|
|
|
| ||
| SURROUND | BASS | SOUND |
| |
| MUTE | VOLUME |
| ||
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press [FM MODE] to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
•If the signal from an FM stereo station is weak and reception is poor, press [FM MODE] to change to monaural reception. The reception may be improved, but the sound will be monaural.
|
|
|
| TU/BAND |
| SOURCE |
|
| FM MODE | VOLUME | PRESET | FM MODE | TEST TONE |
qOPEN/ | a | k | n |
|
|
|
CLOSE |
|
|
| |||
|
|
|
| SURROUND | BASS | SOUND |
f /TUNE - | e /TUNE + d /PRESET c /MEMO |
|
|
| ||
SURROUND | BASS | SOUND | SOURCE |
|
|
|
|
|
|
| MUTE | VOLUME | |
|
|
|
|
|
| |
FM MODE | FM MODE | |||||