Poulan PR185H42STD Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 17

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 12)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

MANDREL

ASSEMBLY

EDGE UP

 

BLADE

 

 

CENTER

 

HOLE

LOCK WASHER

STAR

FLAT WASHER

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE

IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 12

TO SHARPEN BLADE (See Fig. 13)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 13

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents PR185H42STD Safe Operation Practices for Ride-On Mowers Safety RulesBecome ALERT!!! Your Safety is IN- Volved Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Motion Control Lever Selects the speed Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsMulching Mowing Tips Before Each USE Customer ResponsibilitiesGeneral Recommendations Brake Operation TractorTires Operator Presence SystemEngine Clean AIR INTAKE/COOLING Areas Clean AIR ScreenCleaning Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigRecheck side-to-side adjustment Belt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorInterlocks and Relays Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PR185H42STD Schematic2122 Electrical175566 175158175141 121433XChassis 176554 174619174930 159 169473X428 CupholderDrive 175578 175765175556 175410Steering Assembly 177876 175121175146 175118174894 Seat AssemblyWheels and Tires DecalsSpark Arrester Engine Optional EquipmentEngine 143 159 144 150 145 148 Mower Deck146 142 147 147 142174284 17449371081010 173443Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PR185H42STD specifications

The Poulan PR185H42STD is a robust and efficient lawn mower that is designed to meet the needs of residential users looking for a reliable machine for lawn maintenance. This model combines power, versatility, and ease of use, making it an excellent choice for homeowners with medium to large-sized yards.

One of the standout features of the PR185H42STD is its 18.5 HP engine, which provides ample power to tackle a variety of mowing tasks. This Briggs & Stratton engine is known for its durability and performance, ensuring that the mower can handle thick grass and uneven terrain with ease. The engine's overhead valve design contributes to improved fuel efficiency and lower emissions, making it an environmentally friendly option.

The mower is equipped with a 42-inch cutting deck, which allows for wide swath mowing, reducing the time it takes to complete lawn care tasks. The cutting deck is designed with multiple height adjustments, enabling users to customize their cut between 1.5 to 4 inches. This versatility helps achieve the desired lawn height, catering to the varying needs of different grass types and seasonal conditions.

Another notable feature of the Poulan PR185H42STD is its electric start system, which eliminates the hassle often associated with manual pull starts. With the simple turn of a key, the mower roars to life, making it user-friendly and convenient, especially for those who may have difficulty with traditional starting mechanisms.

The PR185H42STD incorporates a hydrostatic transmission that offers smooth and continuous speed adjustment without shifting gears. This technology provides exceptional control over the mower’s speed, allowing users to navigate easily through tight corners and around garden beds. The mower’s tight turning radius further enhances maneuverability, making it suitable for intricate landscaping.

Furthermore, the mower features a comfortable high-back seat and ergonomic steering wheel design, promoting an enjoyable mowing experience. It also comes equipped with a cup holder and storage compartment for added convenience during operation.

With dependable construction and thoughtful design, the Poulan PR185H42STD promises a powerful, user-friendly lawn care solution that stands up to the demands of any residential lawn. Whether you’re maintaining a pristine yard or managing overgrown areas, this mower is a worthy companion for all your lawn maintenance needs.
Top Page Image Contents