Poulan PR185H42STD owner manual Install Seat See Fig

Page 7

ASSEMBLY

SEAT PAN

BATTERY BOX DOOR

TERMINAL

LABEL

TERMINAL

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section, page 10, for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

FIG. 2

INSTALL SEAT (See Fig. 4)

Adjust seat before tightening adjustment knob.

•Roll tractor forward off skid.

•Remove banding holding discharge guard up against tractor.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section, page 10, for location and func- tion of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" po- sition.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

• Get off seat without moving its adjusted position.

• Place motion control lever in neutral (N) position.

• Raise seat and tighten adjustment knob securely.

•

Press lift lever plunger and raise attachment lift lever to

 

 

its highest position.

 

• Start the engine. After engine has started, move throttle

SEAT

 

control to idle position.

 

•

Release parking brake.

 

• Slowly move the motion control lever forward and slowly

 

 

drive tractor off skid.

 

• Apply brake to stop tractor, set parking brake and place

SEAT PAN

 

motion control lever in neutral position.

• Turn ignition key to "OFF" position.

 

 

Continue with the instructions that follow.

SHOULDER

 

 

BOLT

 

 

FLAT WASHER

 

 

ADJUSTMENT

 

 

KNOB

 

 

FIG. 3

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PR185H42STD Safe Operation Practices for Ride-On Mowers Safety RulesBecome ALERT!!! Your Safety is IN- Volved Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Motion Control Lever Selects the speed Know Your TractorHOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips General Recommendations Customer ResponsibilitiesBefore Each USE Operator Presence System TractorBrake Operation TiresEngine Engine OIL Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingRecheck side-to-side adjustment To Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PR185H42STD Schematic2122 Electrical121433X 175158175566 175141Chassis 159 169473X428 Cupholder 174619176554 174930Drive 175410 175765175578 175556Steering Assembly 175118 175121177876 175146174894 Seat AssemblyWheels and Tires DecalsSpark Arrester Engine Optional EquipmentEngine 147 142 Mower Deck143 159 144 150 145 148 146 142 147173443 174493174284 71081010Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PR185H42STD specifications

The Poulan PR185H42STD is a robust and efficient lawn mower that is designed to meet the needs of residential users looking for a reliable machine for lawn maintenance. This model combines power, versatility, and ease of use, making it an excellent choice for homeowners with medium to large-sized yards.

One of the standout features of the PR185H42STD is its 18.5 HP engine, which provides ample power to tackle a variety of mowing tasks. This Briggs & Stratton engine is known for its durability and performance, ensuring that the mower can handle thick grass and uneven terrain with ease. The engine's overhead valve design contributes to improved fuel efficiency and lower emissions, making it an environmentally friendly option.

The mower is equipped with a 42-inch cutting deck, which allows for wide swath mowing, reducing the time it takes to complete lawn care tasks. The cutting deck is designed with multiple height adjustments, enabling users to customize their cut between 1.5 to 4 inches. This versatility helps achieve the desired lawn height, catering to the varying needs of different grass types and seasonal conditions.

Another notable feature of the Poulan PR185H42STD is its electric start system, which eliminates the hassle often associated with manual pull starts. With the simple turn of a key, the mower roars to life, making it user-friendly and convenient, especially for those who may have difficulty with traditional starting mechanisms.

The PR185H42STD incorporates a hydrostatic transmission that offers smooth and continuous speed adjustment without shifting gears. This technology provides exceptional control over the mower’s speed, allowing users to navigate easily through tight corners and around garden beds. The mower’s tight turning radius further enhances maneuverability, making it suitable for intricate landscaping.

Furthermore, the mower features a comfortable high-back seat and ergonomic steering wheel design, promoting an enjoyable mowing experience. It also comes equipped with a cup holder and storage compartment for added convenience during operation.

With dependable construction and thoughtful design, the Poulan PR185H42STD promises a powerful, user-friendly lawn care solution that stands up to the demands of any residential lawn. Whether you’re maintaining a pristine yard or managing overgrown areas, this mower is a worthy companion for all your lawn maintenance needs.
Top Page Image Contents