Poulan PR185H42STD Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

 

ADJUSTMENT

 

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PR185H42STD Safe Operation Practices for Ride-On Mowers Safety RulesBecome ALERT!!! Your Safety is IN- Volved Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Motion Control Lever Selects the speed Know Your TractorHOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelPurge Transmission Mowing TipsMulching Mowing Tips Before Each USE Customer ResponsibilitiesGeneral Recommendations Operator Presence System TractorBrake Operation TiresEngine Engine OIL Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingRecheck side-to-side adjustment To Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PR185H42STD Schematic2122 Electrical121433X 175158175566 175141Chassis 159 169473X428 Cupholder 174619176554 174930Drive 175410 175765175578 175556Steering Assembly 175118 175121177876 175146174894 Seat AssemblyWheels and Tires DecalsSpark Arrester Engine Optional EquipmentEngine 147 142 Mower Deck143 159 144 150 145 148 146 142 147173443 174493174284 71081010Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Sighting Guide Suggested Guide for Sighting Slopes for Safe OperationParts and Service

PR185H42STD specifications

The Poulan PR185H42STD is a robust and efficient lawn mower that is designed to meet the needs of residential users looking for a reliable machine for lawn maintenance. This model combines power, versatility, and ease of use, making it an excellent choice for homeowners with medium to large-sized yards.

One of the standout features of the PR185H42STD is its 18.5 HP engine, which provides ample power to tackle a variety of mowing tasks. This Briggs & Stratton engine is known for its durability and performance, ensuring that the mower can handle thick grass and uneven terrain with ease. The engine's overhead valve design contributes to improved fuel efficiency and lower emissions, making it an environmentally friendly option.

The mower is equipped with a 42-inch cutting deck, which allows for wide swath mowing, reducing the time it takes to complete lawn care tasks. The cutting deck is designed with multiple height adjustments, enabling users to customize their cut between 1.5 to 4 inches. This versatility helps achieve the desired lawn height, catering to the varying needs of different grass types and seasonal conditions.

Another notable feature of the Poulan PR185H42STD is its electric start system, which eliminates the hassle often associated with manual pull starts. With the simple turn of a key, the mower roars to life, making it user-friendly and convenient, especially for those who may have difficulty with traditional starting mechanisms.

The PR185H42STD incorporates a hydrostatic transmission that offers smooth and continuous speed adjustment without shifting gears. This technology provides exceptional control over the mower’s speed, allowing users to navigate easily through tight corners and around garden beds. The mower’s tight turning radius further enhances maneuverability, making it suitable for intricate landscaping.

Furthermore, the mower features a comfortable high-back seat and ergonomic steering wheel design, promoting an enjoyable mowing experience. It also comes equipped with a cup holder and storage compartment for added convenience during operation.

With dependable construction and thoughtful design, the Poulan PR185H42STD promises a powerful, user-friendly lawn care solution that stands up to the demands of any residential lawn. Whether you’re maintaining a pristine yard or managing overgrown areas, this mower is a worthy companion for all your lawn maintenance needs.
Top Page Image Contents