Poulan PP400E Bucking Using a LOG or Support Stand, Limbing, Pruning, Through the limb

Page 11

SWatch for logs with a compression side to prevent the saw from pinching. See il- lustration above for cutting logs with a compression side.

BUCKING USING A LOG OR SUPPORT STAND

S Remember your first cut is always on the compression side of the log. (Refer to the illustration below for your first and second cut)

S Your first cut should extend 1/3 of the diameter of the log.

SFinish with your second cut.

Using a log for support

2nd Cut

1st Cut

1st Cut

2nd Cut

Using a support stand

2nd Cut

1st Cut

1st Cut

2nd Cut

which can cause you to lose your bal- ance or control of the saw.

IMPORTANT POINTS

SWatch out for spring poles. Spring poles are small size limbs which can whip to- ward you or pull you off balance. Use extreme caution when cutting small size

limbs.

S Be alert for spring back from any branches that are bent or under pres- sure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

S Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SLimb a tree only after it is cut down.

S Leave the larger limbs underneath the felled tree to support the tree as you work.

S Start at the base of the felled tree and work toward the top, cutting branches and limbs. Remove small limbs with one cut.

SKeep tree between you and the chain. S Remove larger branches with the cut- ting techniques described BUCKING

WITHOUT A SUPPORT.

S Always use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

S Make your first cut 1/3 of the way through the bottom of the limb. This cut will make the limb sag so that it falls easily on the second cut.

S Next make a second cut all the way

through the limb.

SFinish the pruning operation by using an overcut so that the stump of the limb protrudes 1 to 2 inches (3--5 cm) from the trunk of the tree.

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the mov- ing chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on lad- ders, platforms, a log, or in any position

11

Second cut

First cut 1/3 of way

3rd cut 1 to 2 in. (3--5 cm) from trunk of tree

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 545117548 EnglishEspañol FrançaisPlan Ahead Safety RulesOperate Your SAW Safely Conductor, such as metal fences or pipes Electrical SafetySion and/or causing damage to unit Use a voltage supply as shown on the nameplate of the unitMaintain Control Guard Against KickbackReduce the Chance Kickback Chain Brake and CKA Angle Kickback Safety FeaturesDouble Insulation Construction Either of these reactions may cause youOperation AssemblyStarting Your SAW Before Starting SAW Guide BAR and Chain OILChain Brake Stopping Your SAWFelling Large Trees 6 inches in diameter or larger Cutting MethodsOperating Tips Tree Felling TechniquesBucking Techniques Hinge holds tree on stump and helps control fallCutting a Fallen Tree Bucking Important PointsThrough the limb Bucking Using a LOG or Support StandLimbing PruningMaintenance Service and Adjustments To Replace Chain Chain AdjustmentCustomer Serviceable Parts Steps after each use Troubleshooting Table Cause RemedyStorage Seasonal StorageWarranty Statement

PP400E specifications

The Poulan PP400E is a gas-powered chainsaw designed for homeowners and DIY enthusiasts who need a reliable tool for cutting firewood, clearing brush, or tree trimming. This chainsaw combines power, efficiency, and user-friendly features, making it an excellent choice for a range of cutting tasks.

One of the standout features of the Poulan PP400E is its robust 40cc, 2-cycle engine. This powerful engine provides the necessary torque and cutting speed, allowing users to tackle both light and medium-duty tasks with ease. The engine is engineered for optimum fuel efficiency, giving users longer run times between refuels, which is particularly useful during extended cutting sessions.

The PP400E incorporates a 16-inch bar and chain, which strikes a balance between versatility and control. The 16-inch length is ideal for handling smaller jobs while still providing enough reach for larger branches and logs. The chain is designed for quick and easy adjustments, enabling users to maintain proper tension without the need for complex tools, making it more convenient for those less experienced with chainsaw maintenance.

Safety is a top priority in the design of the PP400E, which includes a chain brake system that instantly stops the chain in the event of kickback, offering peace of mind during operation. Additionally, the chainsaw features a comfort grip handle, which is ergonomically designed to reduce fatigue and enhance control, allowing users to work for longer periods without excessive strain.

The Poulan PP400E also features an automatic oiler that delivers a steady supply of lubrication to the chain and bar, ensuring efficient operation and prolonging the life of the cutting components. This system is particularly beneficial for maintaining optimal performance in various cutting conditions.

In terms of design, the Poulan PP400E is relatively lightweight compared to other chainsaws in its class, making it easy to handle and maneuver. Its compact design contributes to its portability, allowing users to transport it easily to different job sites.

Overall, the Poulan PP400E stands out as a versatile and dependable chainsaw that meets the needs of casual users and serious hobbyists alike. With its powerful engine, user-friendly features, and commitment to safety, the PP400E is a smart investment for anyone looking to tackle outdoor cutting tasks with efficiency and ease.
Top Page Image Contents