Poulan PP400E instruction manual To Replace Chain, Chain Adjustment, Customer Serviceable Parts

Page 14

It is normal for a new chain to stretch dur- ing the first 15 minutes of operation. You should recheck your chain tension fre- quently and adjust the chain tension as required. See CHECK CHAIN TENSION section.

Replace the old chain when it becomes worn or damaged. Use only the Low Kickback replacement chain specified in the list of available replacement parts. The chain must comply with kickback re- quirements of ANSI B175.1 when tested with this saw. See your authorized ser- vice dealer to replace and sharpen indi- vidual cutters on your chain.

TO REPLACE CHAIN:

1.Disconnect the chain saw from the power source.

2.Remove bar clamp nuts.

3.Remove bar clamp and old chain.

Bar Clamp

Nuts

Bar

Adjusting Screw

Clamp

 

4.Turn the adjusting screw counter- clockwise to move the adjusting pin almost as far as it will go to the rear. Do not remove the adjusting screw from the bar clamp.

5.Carefully remove the new chain from the package. Hold chain with cutters facing as shown.

Tip of

Bar

CUTTERS MUST FACE IN

DIRECTION OF ROTATION

Cutters

Depth Gauge

Drive Links

6.Place chain around the sprocket and fit the drive links into the guide bar groove and then into the teeth of the sprocket in the tip of the guide bar.

7.Hold the guide bar against the saw frame and install the bar clamp. Be sure adjusting pin is in the adjusting pin hole in the bar.

Inside view of Bar Clamp

Adjusting pin hole

Adjusting screw

Adjusting pin

8.Secure the guide bar and bar clamp with the bar clamp nuts; tighten

finger tight only.

CAUTION: If saw chain is installed back- wards, the saw will vibrate excessively and will not cut wood.

CHAIN ADJUSTMENT

See CHECK CHAIN TENSION in the MAIN-

TENANCE section.

CUSTOMER SERVICEABLE PARTS

WARNING: Use of any other ac- cessory or attachment might present a risk of injury to the operator.

REPLACEMENT PART

PART NO.

 

 

Hex Nuts

530015917

Oil Cap

530053072

Bar Adjusting Screw

530016265

Bar Adjusting Pin

530053068

File (5/32″ dia.) Twin Pak

952055085

Xtra GUARDr Chain --18″

952051338

Lo--KickrGuide Bar -- 18″

952044418

Bar & Chain Lubricant --1 qt.

952030203

Bar & Chain Lubricant --1 gal.

952030204

 

 

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Français EnglishEspañol 545117548Plan Ahead Safety RulesOperate Your SAW Safely Use a voltage supply as shown on the nameplate of the unit Electrical SafetySion and/or causing damage to unit Conductor, such as metal fences or pipesMaintain Control Guard Against KickbackReduce the Chance Kickback Kickback Safety Features Chain Brake and CKA AngleEither of these reactions may cause you Double Insulation ConstructionAssembly OperationStopping Your SAW Before Starting SAW Guide BAR and Chain OILChain Brake Starting Your SAWTree Felling Techniques Cutting MethodsOperating Tips Felling Large Trees 6 inches in diameter or largerImportant Points Hinge holds tree on stump and helps control fallCutting a Fallen Tree Bucking Bucking TechniquesPruning Bucking Using a LOG or Support StandLimbing Through the limbMaintenance Service and Adjustments To Replace Chain Chain AdjustmentCustomer Serviceable Parts Seasonal Storage Troubleshooting Table Cause RemedyStorage Steps after each useWarranty Statement

PP400E specifications

The Poulan PP400E is a gas-powered chainsaw designed for homeowners and DIY enthusiasts who need a reliable tool for cutting firewood, clearing brush, or tree trimming. This chainsaw combines power, efficiency, and user-friendly features, making it an excellent choice for a range of cutting tasks.

One of the standout features of the Poulan PP400E is its robust 40cc, 2-cycle engine. This powerful engine provides the necessary torque and cutting speed, allowing users to tackle both light and medium-duty tasks with ease. The engine is engineered for optimum fuel efficiency, giving users longer run times between refuels, which is particularly useful during extended cutting sessions.

The PP400E incorporates a 16-inch bar and chain, which strikes a balance between versatility and control. The 16-inch length is ideal for handling smaller jobs while still providing enough reach for larger branches and logs. The chain is designed for quick and easy adjustments, enabling users to maintain proper tension without the need for complex tools, making it more convenient for those less experienced with chainsaw maintenance.

Safety is a top priority in the design of the PP400E, which includes a chain brake system that instantly stops the chain in the event of kickback, offering peace of mind during operation. Additionally, the chainsaw features a comfort grip handle, which is ergonomically designed to reduce fatigue and enhance control, allowing users to work for longer periods without excessive strain.

The Poulan PP400E also features an automatic oiler that delivers a steady supply of lubrication to the chain and bar, ensuring efficient operation and prolonging the life of the cutting components. This system is particularly beneficial for maintaining optimal performance in various cutting conditions.

In terms of design, the Poulan PP400E is relatively lightweight compared to other chainsaws in its class, making it easy to handle and maneuver. Its compact design contributes to its portability, allowing users to transport it easily to different job sites.

Overall, the Poulan PP400E stands out as a versatile and dependable chainsaw that meets the needs of casual users and serious hobbyists alike. With its powerful engine, user-friendly features, and commitment to safety, the PP400E is a smart investment for anyone looking to tackle outdoor cutting tasks with efficiency and ease.
Top Page Image Contents