Poulan PP400E instruction manual Service and Adjustments

Page 13

Adjusting Screw

5.Check the tension by lifting the chain from the guide bar. Remove some of the stiffness in the chain by pulling down and letting go of the chain sever- al times.

6.Continue turning the adjusting screw until the tension is correct (see step 4).

7.Tighten bar clamp nuts with a wrench.

8.Recheck chain tension.

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious in- jury.

CHECK CHAIN SHARPNESS

A sharp chain makes wood chips. A dull chain makes a sawdust powder and cuts slowly. See CHAIN SHARPENING in the SERVICE AND ADJUSTMENTS section.

CHECK GUIDE BAR

Conditions which require guide bar main- tenance:

SSaw cuts to one side or at an angle. S Saw has to be forced through the cut. S Inadequate supply of oil to the bar and

chain.

Check the condition of the guide bar each time the chain is sharpened. A worn guide bar will damage the chain and make cut- ting difficult.

After each use, with unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

S Disconnect the chain saw from the pow- er source.

S Loosen and remove bar clamp nuts. Remove bar and chain from saw.

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to restore square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace the guide bar when the groove is worn, the guide bar is bent or crack--ed, or when excess heating or burring of the rails occurs. If replacement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

LUBRICATION

Bar Oil Fill Cap

SCheck bar and chain oil before use and every 15 minutes while operating the saw. See GUIDE BAR AND CHAIN OIL un- der the OPERATION section.

INSPECT AND CLEAN UNIT AND LABELS

SAfter each use, inspect complete unit for

loose or damaged parts. Clean the unit and labels using a damp cloth with a mild detergent.

SWipe off the unit and labels with a clean dry cloth.

SERVICE AND ADJUSTMENTS

CHAIN SHARPENING

Chain sharpening requires special tools. You can purchase sharpening tools at an authorized service dealer or go to a pro- fessional chain sharpener.

WARNING: Avoid accidental start- ing. Always unplug saw from power source before installing a bar and/or chain.

CHAIN REPLACEMENT

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Español EnglishFrançais 545117548Operate Your SAW Safely Safety RulesPlan Ahead Sion and/or causing damage to unit Electrical SafetyUse a voltage supply as shown on the nameplate of the unit Conductor, such as metal fences or pipesReduce the Chance Kickback Guard Against KickbackMaintain Control Chain Brake and CKA Angle Kickback Safety FeaturesDouble Insulation Construction Either of these reactions may cause youOperation AssemblyChain Brake Before Starting SAW Guide BAR and Chain OILStopping Your SAW Starting Your SAWOperating Tips Cutting MethodsTree Felling Techniques Felling Large Trees 6 inches in diameter or largerCutting a Fallen Tree Bucking Hinge holds tree on stump and helps control fallImportant Points Bucking TechniquesLimbing Bucking Using a LOG or Support StandPruning Through the limbMaintenance Service and Adjustments Customer Serviceable Parts Chain AdjustmentTo Replace Chain Storage Troubleshooting Table Cause RemedySeasonal Storage Steps after each useWarranty Statement

PP400E specifications

The Poulan PP400E is a gas-powered chainsaw designed for homeowners and DIY enthusiasts who need a reliable tool for cutting firewood, clearing brush, or tree trimming. This chainsaw combines power, efficiency, and user-friendly features, making it an excellent choice for a range of cutting tasks.

One of the standout features of the Poulan PP400E is its robust 40cc, 2-cycle engine. This powerful engine provides the necessary torque and cutting speed, allowing users to tackle both light and medium-duty tasks with ease. The engine is engineered for optimum fuel efficiency, giving users longer run times between refuels, which is particularly useful during extended cutting sessions.

The PP400E incorporates a 16-inch bar and chain, which strikes a balance between versatility and control. The 16-inch length is ideal for handling smaller jobs while still providing enough reach for larger branches and logs. The chain is designed for quick and easy adjustments, enabling users to maintain proper tension without the need for complex tools, making it more convenient for those less experienced with chainsaw maintenance.

Safety is a top priority in the design of the PP400E, which includes a chain brake system that instantly stops the chain in the event of kickback, offering peace of mind during operation. Additionally, the chainsaw features a comfort grip handle, which is ergonomically designed to reduce fatigue and enhance control, allowing users to work for longer periods without excessive strain.

The Poulan PP400E also features an automatic oiler that delivers a steady supply of lubrication to the chain and bar, ensuring efficient operation and prolonging the life of the cutting components. This system is particularly beneficial for maintaining optimal performance in various cutting conditions.

In terms of design, the Poulan PP400E is relatively lightweight compared to other chainsaws in its class, making it easy to handle and maneuver. Its compact design contributes to its portability, allowing users to transport it easily to different job sites.

Overall, the Poulan PP400E stands out as a versatile and dependable chainsaw that meets the needs of casual users and serious hobbyists alike. With its powerful engine, user-friendly features, and commitment to safety, the PP400E is a smart investment for anyone looking to tackle outdoor cutting tasks with efficiency and ease.
Top Page Image Contents