Poulan P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH

Page 10

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in completely (to the OFF CHOKE position) and then following the warm engine starting procedure listed above. Ensure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020″ (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions 545137224 11/30/06Plan Ahead Starting ReminderTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Assembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Primer Bulb Throttle LOCK-OUT Chain BrakeCHOKE/FAST Idle Lever Before Starting EngineDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Right Foot Through Rear HandleOperating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support LimbingService Cleaning the Spark ARREST- ING Screen Inspect and Clean Unit and DecalsClean AIR Filter Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Limited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair

P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH specifications

The Poulan line of chainsaws has established a strong reputation among both amateur and professional users for their reliability, performance, and innovative features. In this article, we delve into several notable models: the P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, and P4018AV BH.

Starting with the Poulan P3314, this chainsaw is powered by a robust 33cc two-cycle engine, delivering exceptional cutting power for light to medium-duty tasks. Its 14-inch bar provides a perfect balance between agility and efficiency. The tool-less chain tension system is another highlight, allowing users to easily adjust the chain without needing additional tools, enhancing usability.

The P3314WS and P3314WSA models build upon this foundation, introducing enhanced features like an automatic oiler for consistent lubrication during operation, thus prolonging the life of the bar and chain. The P3314WSA also includes an anti-vibration system, providing increased comfort during extended use, reducing operator fatigue.

Next, the Poulan P3416 offers a slightly larger 34cc engine, making it ideal for tackling larger projects while still maintaining a lightweight, easy-to-handle design. Its 16-inch bar is perfect for larger cuts, and the convenient primer bulb aids in easy starting, even in colder weather.

The P3516PR takes performance a step further with a powerful 35cc engine. This model excels in versatility, suitable for both home use and light commercial tasks. Its ergonomic design, along with the lightweight build, enables users to handle the chainsaw comfortably for longer periods.

For those requiring even more power, the P4018WM and P4018WT feature an 40cc engine, capable of handling tougher jobs effortlessly. Both models come equipped with an 18-inch bar, making them well-suited for cutting larger logs or clearing heavy brush. The addition of an easy-access air filter allows for straightforward maintenance, thereby increasing the chainsaw’s longevity.

The P3818AV introduces advanced anti-vibration technology, further enhancing user comfort, while the P4018AV and P4018AV BH models offer specialized features like the brushless motor for greater efficiency and durability. These advanced models are engineered for professionals who demand the highest performance and reliability.

Overall, the Poulan chainsaw lineup provides a range of options tailored to different user needs, from occasional home projects to intense commercial tasks. Each model showcases Poulan's commitment to delivering innovative features that elevate the cutting experience, making them a popular choice for users at all skill levels.
Top Page Image Contents