Poulan P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH

Page 17

HELPFUL TIP

During storage of your gas/ oil mixture, the oil will sepa- rate from the gas.

We recommend that you shake the gas can weekly to insure proper blending of the gas and oil.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distrib- ute oil.

SReplace spark plug with new one of rec- ommended type and heat range.

SClean air filter.

SCheck entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

SAt the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to

another.

S Replace your gasoline can if it starts to rust.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

 

TROUBLE

CAUSE

REMEDY

 

 

 

 

 

 

 

Engine will not

1. Ignition switch off.

1.

Move ignition switch to ON.

 

start or will run

2. Engine flooded.

2.

See “Difficult Starting” in

 

only a few

 

 

 

Operation Section.

 

seconds after

3. Fuel tank empty.

3.

Fill tank with correct fuel mixture.

 

starting.

4. Spark plug not firing.

4.

Install new spark plug.

 

 

5. Fuel not reaching

5.

Check for dirty fuel filter; replace.

 

 

 

carburetor.

 

Check for kinked or split fuel line;

 

 

 

 

 

repair or replace.

 

 

 

 

 

 

 

Engine will

1.

Idle speed requires

1. See “Carburetor Adjustment” in the

 

not idle

 

adjustment.

 

Service and Adjustments Section.

 

properly.

2.

Carburetor requires

2. Contact an authorized service dealer.

 

 

 

adjustment.

 

 

 

 

Engine will not

1.

Air filter dirty.

1. Clean or replace air filter.

 

accelerate,

2.

Spark plug fouled.

2. Clean or replace plug and regap.

 

lacks power,

3.

Chain brake engaged.

3. Disengage chain brake.

 

or dies under

4.

Carburetor requires

4. Contact an authorized service dealer.

 

a load.

 

adjustment.

 

 

 

 

Engine

1.

Too much oil mixed with

1.

Empty fuel tank and refill with

 

 

smokes

 

gasoline.

 

correct fuel mixture.

 

excessively.

 

 

 

 

 

 

Chain moves

1. Idle speed requires

1. See “Carburetor Adjustment” in the

 

at idle speed.

 

adjustment.

 

Service and Adjustments Section.

 

 

2. Clutch requires repair.

2.

Contact an authorized service dealer.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 545137224 11/30/06 Manual de Instrucciones Manuel d’InstructionsTions found in this manual Starting ReminderPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Attaching the BAR & Chain If not AssemblyChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation CHOKE/FAST Idle Lever Throttle LOCK-OUT Chain BrakePrimer Bulb Before Starting EngineStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingService Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Other Load Adjustment EngineEngine Ligations The U.S. Environmental Limited WarrantyNANCE, Replacement and Repair

P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH specifications

The Poulan line of chainsaws has established a strong reputation among both amateur and professional users for their reliability, performance, and innovative features. In this article, we delve into several notable models: the P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, and P4018AV BH.

Starting with the Poulan P3314, this chainsaw is powered by a robust 33cc two-cycle engine, delivering exceptional cutting power for light to medium-duty tasks. Its 14-inch bar provides a perfect balance between agility and efficiency. The tool-less chain tension system is another highlight, allowing users to easily adjust the chain without needing additional tools, enhancing usability.

The P3314WS and P3314WSA models build upon this foundation, introducing enhanced features like an automatic oiler for consistent lubrication during operation, thus prolonging the life of the bar and chain. The P3314WSA also includes an anti-vibration system, providing increased comfort during extended use, reducing operator fatigue.

Next, the Poulan P3416 offers a slightly larger 34cc engine, making it ideal for tackling larger projects while still maintaining a lightweight, easy-to-handle design. Its 16-inch bar is perfect for larger cuts, and the convenient primer bulb aids in easy starting, even in colder weather.

The P3516PR takes performance a step further with a powerful 35cc engine. This model excels in versatility, suitable for both home use and light commercial tasks. Its ergonomic design, along with the lightweight build, enables users to handle the chainsaw comfortably for longer periods.

For those requiring even more power, the P4018WM and P4018WT feature an 40cc engine, capable of handling tougher jobs effortlessly. Both models come equipped with an 18-inch bar, making them well-suited for cutting larger logs or clearing heavy brush. The addition of an easy-access air filter allows for straightforward maintenance, thereby increasing the chainsaw’s longevity.

The P3818AV introduces advanced anti-vibration technology, further enhancing user comfort, while the P4018AV and P4018AV BH models offer specialized features like the brushless motor for greater efficiency and durability. These advanced models are engineered for professionals who demand the highest performance and reliability.

Overall, the Poulan chainsaw lineup provides a range of options tailored to different user needs, from occasional home projects to intense commercial tasks. Each model showcases Poulan's commitment to delivering innovative features that elevate the cutting experience, making them a popular choice for users at all skill levels.
Top Page Image Contents