Poulan P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH

Page 7

Inside view of clutch cover

Adjustment located on clutch cover

4.Turn the adjusting screw by hand coun- terclockwise until the adjusting pin just touches the stop. This should allow the pin to be near the correct position.

5.Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket.

Bar bolts

Guide bar

6.Carefully remove the chain from the pack- age. Hold chain with the drive links as shown.

Tip of

Bar

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Cutters

Depth Gauge

Drive Links

7.Place chain over and behind clutch re- tainer, fitting the drive links in the clutch drum sprocket.

8.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

9.Fit chain drive links into bar groove.

10.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

11.Now, install clutch cover making sure the adjusting pin is positioned in the low- er hole in the guide bar. Remember this pin moves the bar forward and back- ward as the screw is turned.

Clutch

Cover

Adjusting Pin Lower

Hole

Guide Bar

12.Install bar nuts and finger tighten only. Once the chain is tensioned, you will need to tighten bar nuts.

CHAIN TENSION

(Including units with chain already installed)

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

NOTE: When adjusting chain tension, make sure the bar nuts are finger tight only. Attempting to tension the chain when the bar nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move chain around guide bar. If the chain does not rotate, it is too tight. If the chain is too loose, it will sag below the bar.

Guide

Bar

Chain Adjustmen

Bar Nuts Adjusting Tool

Screw (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

1.Loosen bar nuts until they are finger tight against the clutch cover.

2.Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail.

Adjusting

Screw

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 545137224 11/30/06 Manual de Instrucciones Manuel d’InstructionsPlan Ahead Starting ReminderTions found in this manual Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pull-In Reduce the Chance of KickbackMaintain Control Avoid Pinch-KickbackChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Attaching the BAR & Chain If not AssemblyChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Before Starting Engine Throttle LOCK-OUT Chain BrakeCHOKE/FAST Idle Lever Primer BulbRight Foot Through Rear Handle Important Points to RememberStarting a Warm Engine Difficult Starting or starting a flooded engineTree Felling Techniques Braking function control Caution The chain brake must beInertia activating function control Operating TipsImportant Points Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen TreeLimbing Bucking Using a LOG or Support StandBucking Without a Support Limbing and Pruning Important PointsService Check Fuel Mixture Level Inspect and Clean Unit and DecalsClean AIR Filter Cleaning the Spark ARREST- ING ScreenStorage Engine Load Adjustment EngineOther Ligations The U.S. Environmental Limited WarrantyNANCE, Replacement and Repair

P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH specifications

The Poulan line of chainsaws has established a strong reputation among both amateur and professional users for their reliability, performance, and innovative features. In this article, we delve into several notable models: the P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, and P4018AV BH.

Starting with the Poulan P3314, this chainsaw is powered by a robust 33cc two-cycle engine, delivering exceptional cutting power for light to medium-duty tasks. Its 14-inch bar provides a perfect balance between agility and efficiency. The tool-less chain tension system is another highlight, allowing users to easily adjust the chain without needing additional tools, enhancing usability.

The P3314WS and P3314WSA models build upon this foundation, introducing enhanced features like an automatic oiler for consistent lubrication during operation, thus prolonging the life of the bar and chain. The P3314WSA also includes an anti-vibration system, providing increased comfort during extended use, reducing operator fatigue.

Next, the Poulan P3416 offers a slightly larger 34cc engine, making it ideal for tackling larger projects while still maintaining a lightweight, easy-to-handle design. Its 16-inch bar is perfect for larger cuts, and the convenient primer bulb aids in easy starting, even in colder weather.

The P3516PR takes performance a step further with a powerful 35cc engine. This model excels in versatility, suitable for both home use and light commercial tasks. Its ergonomic design, along with the lightweight build, enables users to handle the chainsaw comfortably for longer periods.

For those requiring even more power, the P4018WM and P4018WT feature an 40cc engine, capable of handling tougher jobs effortlessly. Both models come equipped with an 18-inch bar, making them well-suited for cutting larger logs or clearing heavy brush. The addition of an easy-access air filter allows for straightforward maintenance, thereby increasing the chainsaw’s longevity.

The P3818AV introduces advanced anti-vibration technology, further enhancing user comfort, while the P4018AV and P4018AV BH models offer specialized features like the brushless motor for greater efficiency and durability. These advanced models are engineered for professionals who demand the highest performance and reliability.

Overall, the Poulan chainsaw lineup provides a range of options tailored to different user needs, from occasional home projects to intense commercial tasks. Each model showcases Poulan's commitment to delivering innovative features that elevate the cutting experience, making them a popular choice for users at all skill levels.
Top Page Image Contents