Poulan P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH

Page 9

THROTTLE LOCK-OUT

CHAIN BRAKE

 

 

The THROTTLE LOCK--OUT must be

The chain brake is a device designed to stop

pressed before you can squeeze the throttle

the chain if kickback occurs. The chain brake

trigger. This feature prevents you from acci-

activates automatically in the event of kick-

dentally squeezing the trigger.

back. The chain brake activates manually if the

CHOKE/FAST IDLE LEVER

front hand guard is pushed forward. The chain

The choke and fast idle are set by pulling the

brake is disengaged by pulling the front hand

guard back toward the front handle as far as

CHOKE/FAST IDLE LEVER out to the full ex-

possible.

 

 

 

tent for cold starting or after refueling. The

 

 

 

 

 

 

 

choke provides additional fuel to the engine

CHAIN TENSION

 

 

during cold starting.

It is normal for a new chain to stretch during the

PRIMER BULB

first 15 minutes of operation. You should check

The PRIMER BULB circulates fuel to the car-

your chain tension frequently. See CHAIN

buretor to provide quicker starting.

TENSION under the ASSEMBLY section.

 

 

 

 

 

 

WARNING: Muffler is very hot dur-

In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a

ing and after use. Do not touch the muffler or

small amount (5 to 10%) of #1 Diesel Fuel or

allow combustible material such as dry

kerosene.

Bar and chain oil must be free

grass or fuel to do so.

flowing for the oil system to pump enough oil

BEFORE STARTING ENGINE

for adequate lubrication.

 

 

 

 

Genuine Poulan bar and chain oil is recom-

WARNING: Be sure to read the fuel

mended to protect your unit against exces-

handling information in the safety rules sec-

sive wear from heat and friction. Poulan

oil

resists high temperature thinning.

 

 

tion of this manual before you begin. If you do

 

 

If Poulan

bar and chain oil is not available,

not understand the fuel handling information

do not attempt to fuel your unit. Seek help

use a good grade SAE 30 oil.

 

 

from someone that does understand the in-

S Never use waste oil for bar and chain lubri-

formation or call the customer assistance

cation.

 

 

 

help line at 1-800-554-6723.

S Always stop the engine before removing

FUELING ENGINE

the oil cap.

 

 

WARNING: Remove fuel cap slow-

IMPORTANT

 

 

Experience indicates that alcohol--blended

ly when refueling.

fuels (called gasohol or using ethanol or meth-

HELPFUL TIP

 

anol) can attract moisture which leads to sepa-

 

ration and formation of acids during storage.

To obtain the correct oil mix

 

Acidic gas can damage the fuel system of an

ratio, pour 3.2 ounces of

 

engine while in storage. To avoid engine prob-

2-cycle synthetic oil into

 

lems, the fuel system should be emptied before

one gallon of fresh gas.

 

storage for 30 days or longer. Drain the gas

This engine is certified to operate on unleaded

 

tank, start the engine and let it run until the fuel

gasoline. Before operation, gasoline must be

lines and carburetor are empty. Use fresh fuel

mixed with a good quality synthetic 2-cycle air-

next season. See STORAGE section for addi-

cooled engine oil designed to be mixed at a ra-

tional information.

 

 

tio of 40:1. Poulan/WEED EATER brand syn-

CHAIN BRAKE

 

 

thetic oil is recommended. A 40:1 ratio is

Ensure chain brake is disengaged by pulling

obtained by mixing 3.2 ounces (95 ml) of oil

the front hand guard back toward the front han-

with 1 gallon (4 liters) of unleaded gasoline. In-

dle as far as possible. The chain brake must be

cluded with this saw is a 3.2 ounce (95 ml) con-

disengaged before cutting with the saw.

 

 

tainer of Poulan/WEED EATER brand synthet-

 

 

 

 

ic oil. Pour the entire contents of this container

WARNING: The chain must not

into 1 gallon (4 liters) of gasoline to achieve the

move when the engine runs at idle speed. If

proper fuel mixture. DO NOT USE automotive

the chain moves at idle speed refer to CAR-

or marine oil. These oils will cause engine dam-

BURETOR ADJUSTMENT within

this

age. When mixing fuel follow the instructions

manual. Avoid contact with the muffler. A hot

printed on the container. Always read and fol-

muffler can cause serious burns.

 

 

low the safety rules listed under HANDLE

 

 

 

 

 

 

FUEL WITH CAUTION.

To stop the engine move the ON/STOP

BAR AND CHAIN LUBRICATION

switch to the STOP position.

 

 

The bar and chain require continuous lubri-

 

 

 

 

cation. Lubrication is provided by the auto-

To start the engine hold the saw firmly on the

matic oiler system when the oil tank is kept

ground as illustrated. Make sure the chain is

filled. Lack of oil will quickly ruin the bar and

free to turn without contacting any object.

chain. Too little oil will cause overheating

 

shown by smoke coming from the chain and/

 

or discoloration of the bar.

 

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 545137224 11/30/06 Manual de Instrucciones Manuel d’InstructionsStarting Reminder Plan AheadTions found in this manual Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InKickback Safety Features Chain Brake and CKA AngleChain saws as set by Ansi B175.1 Attaching the BAR & Chain If not AssemblyAdjusting the tension Chain TensionChecking the tension ON/STOP Switch Throttle Trigger OperationKnow Your Chain SAW CHOKE/FAST Idle Lever Throttle LOCK-OUT Chain BrakePrimer Bulb Before Starting EngineStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points LimbingService Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Load Adjustment Engine EngineOther Ligations The U.S. Environmental Limited WarrantyNANCE, Replacement and Repair

P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, P4018AV BH specifications

The Poulan line of chainsaws has established a strong reputation among both amateur and professional users for their reliability, performance, and innovative features. In this article, we delve into several notable models: the P3314, P3314WS, P3314WSA, P3416, P3516PR, P4018WM, P4018WT, P3818AV, P4018AV, and P4018AV BH.

Starting with the Poulan P3314, this chainsaw is powered by a robust 33cc two-cycle engine, delivering exceptional cutting power for light to medium-duty tasks. Its 14-inch bar provides a perfect balance between agility and efficiency. The tool-less chain tension system is another highlight, allowing users to easily adjust the chain without needing additional tools, enhancing usability.

The P3314WS and P3314WSA models build upon this foundation, introducing enhanced features like an automatic oiler for consistent lubrication during operation, thus prolonging the life of the bar and chain. The P3314WSA also includes an anti-vibration system, providing increased comfort during extended use, reducing operator fatigue.

Next, the Poulan P3416 offers a slightly larger 34cc engine, making it ideal for tackling larger projects while still maintaining a lightweight, easy-to-handle design. Its 16-inch bar is perfect for larger cuts, and the convenient primer bulb aids in easy starting, even in colder weather.

The P3516PR takes performance a step further with a powerful 35cc engine. This model excels in versatility, suitable for both home use and light commercial tasks. Its ergonomic design, along with the lightweight build, enables users to handle the chainsaw comfortably for longer periods.

For those requiring even more power, the P4018WM and P4018WT feature an 40cc engine, capable of handling tougher jobs effortlessly. Both models come equipped with an 18-inch bar, making them well-suited for cutting larger logs or clearing heavy brush. The addition of an easy-access air filter allows for straightforward maintenance, thereby increasing the chainsaw’s longevity.

The P3818AV introduces advanced anti-vibration technology, further enhancing user comfort, while the P4018AV and P4018AV BH models offer specialized features like the brushless motor for greater efficiency and durability. These advanced models are engineered for professionals who demand the highest performance and reliability.

Overall, the Poulan chainsaw lineup provides a range of options tailored to different user needs, from occasional home projects to intense commercial tasks. Each model showcases Poulan's commitment to delivering innovative features that elevate the cutting experience, making them a popular choice for users at all skill levels.
Top Page Image Contents