Poulan BH2160 LE Carburetor Adjustment, BAR Maintenance, Chain Sharpening, Ignition Timing

Page 15

Exhaust

Outlet

Outlet Cover

SClean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Exhaust Outlet must face chain brake (bar side) of chain saw

10.Inspect the muffler gasket and replace if damaged.

11.Reinstall backplate, outlet guide, muffler gasket, and muffler using muffler bolts. Tighten until secure.

12.Reinstall bolt cover and locknut. Tighten securely.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle speed screw (T) clockwise to in- crease engine speed.

STurn idle speed screw (T) counterclock- wise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call 1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced through the cut, or been run with an improper amount of bar lubrication it may be neces- sary to service your bar. A worn bar will dam- age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SMove ON/STOP switch to the STOP posi- tion.

SLoosen and remove chain brake nuts and chain brake. Remove bar and chain from saw.

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when exce-

ssheating or burring of the rails occurs. If re- placement is necessary, use only the guide bar specified for your saw in the repair parts list or on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0.6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Screws

Cylinder

Spark

Cover

 

Plug Boot

 

Spark

 

Plug

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 16/04 English Español FrançaisIdentification of Symbols Safety RulesPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionKickback Safety Features Reduce the Chance of KickbackMaintain Control 952044370 Chain Brake and CKA AngleFront Hand Guard, designed to reduce Back toward the operatorChain Brake Nuts AssemblyInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notAdjusting the tension Checking the tensionChain Tension Throttle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationCutting Methods Starting a Warm EngineImportant Points Direction of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen AIR FilterIgnition Timing Carburetor AdjustmentBAR Maintenance Chain SharpeningNeed ASSISTANCE? Need Service PART?Need ASSISTANCE? StorageTions The U.S. Environmental Protection Limited WarrantyPlacement and Repair of Emission

BH2160 LE specifications

The Poulan BH2160 LE is a versatile and robust hedge trimmer designed for homeowners and landscaping professionals alike. As part of Poulan’s esteemed line of outdoor power equipment, the BH2160 LE delivers outstanding cutting performance, making it an essential tool for maintaining your garden and yard.

One of the standout features of the BH2160 LE is its powerful 24cc, 2-cycle engine. This engine offers an impressive balance of power and efficiency, enabling users to tackle thick and dense hedges with ease. The lightweight design of the trimmer, combined with its ergonomic handle, ensures comfort during extended use, reducing fatigue and allowing for precise maneuverability.

The BH2160 LE is equipped with a 22-inch dual reciprocating blade, designed for efficient and smooth cutting. The sharpened cutting edges of the blades provide a clean cut, promoting healthy growth in hedges and shrubs. One notable technology incorporated into the design is the anti-vibration system, which minimizes vibrations transmitted to the operator, thus enhancing comfort during operation.

Another key characteristic of the Poulan BH2160 LE is its availability with an adjustable handle. This feature allows users to customize their grip position according to their personal preference and the nature of the task at hand. Additionally, the trimmer’s built-in blade guard adds an extra layer of safety, protecting both the user and the blades from damage during storage and transportation.

For ease of use and maintenance, the BH2160 LE comes with a tool-less air filter access feature. This innovation simplifies filter cleaning and replacement, extending the lifespan of the engine and ensuring optimal performance. Moreover, the model features a fuel tank designed for easy refueling and minimizes the risk of spills.

Overall, the Poulan BH2160 LE is a powerful, user-friendly hedge trimmer that combines efficiency with comfort. Its advanced engine technology, sharp dual blades, and ergonomic design make it a dependable choice for those looking to maintain their outdoor spaces. Whether tackling overgrown hedges or shaping ornamental shrubs, the BH2160 LE offers reliability and power suitable for a variety of gardening tasks.
Top Page Image Contents