Poulan BH2160 LE instruction manual Starting, Fueling Engine, BAR and Chain Lubrication

Page 9

FUELING & LUBRICATION

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gaso- line. Included with this saw is a 3.2 ounce con- tainer of Poulan/Weed Eater brand synthetic oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine PoulanR bar and chain oil is recom- mended to protect your unit against exces- sive wear from heat and friction. PoulanR oil resists high temperature thinning.

If PoulanR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system

should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (38 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 16/04 English Español FrançaisIdentification of Symbols Safety RulesPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackKickback Safety Features Reduce the Chance of KickbackMaintain Control Front Hand Guard, designed to reduce Chain Brake and CKA AngleBack toward the operator 952044370Inside view Chain Brake Adjustment located on Chain Brake AssemblyAttaching the BAR & Chain If not Chain Brake NutsAdjusting the tension Checking the tensionChain Tension Know Your Chain SAW ON/STOP SwitchThrottle Trigger Throttle LOCK-OUTFueling Engine StartingBAR and Chain Lubrication Important Points to RememberCutting Methods Starting a Warm EngineImportant Points Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Direction of FallCutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportLimbing and Pruning Important Points ServiceLimbing PruningCleaning the Spark ARREST- ING Screen Cleaning the air filterAIR Filter Inspect Muffler and Spark Arresting ScreenBAR Maintenance Carburetor AdjustmentChain Sharpening Ignition TimingNeed ASSISTANCE? Need Service PART?Storage Need ASSISTANCE?Tions The U.S. Environmental Protection Limited WarrantyPlacement and Repair of Emission

BH2160 LE specifications

The Poulan BH2160 LE is a versatile and robust hedge trimmer designed for homeowners and landscaping professionals alike. As part of Poulan’s esteemed line of outdoor power equipment, the BH2160 LE delivers outstanding cutting performance, making it an essential tool for maintaining your garden and yard.

One of the standout features of the BH2160 LE is its powerful 24cc, 2-cycle engine. This engine offers an impressive balance of power and efficiency, enabling users to tackle thick and dense hedges with ease. The lightweight design of the trimmer, combined with its ergonomic handle, ensures comfort during extended use, reducing fatigue and allowing for precise maneuverability.

The BH2160 LE is equipped with a 22-inch dual reciprocating blade, designed for efficient and smooth cutting. The sharpened cutting edges of the blades provide a clean cut, promoting healthy growth in hedges and shrubs. One notable technology incorporated into the design is the anti-vibration system, which minimizes vibrations transmitted to the operator, thus enhancing comfort during operation.

Another key characteristic of the Poulan BH2160 LE is its availability with an adjustable handle. This feature allows users to customize their grip position according to their personal preference and the nature of the task at hand. Additionally, the trimmer’s built-in blade guard adds an extra layer of safety, protecting both the user and the blades from damage during storage and transportation.

For ease of use and maintenance, the BH2160 LE comes with a tool-less air filter access feature. This innovation simplifies filter cleaning and replacement, extending the lifespan of the engine and ensuring optimal performance. Moreover, the model features a fuel tank designed for easy refueling and minimizes the risk of spills.

Overall, the Poulan BH2160 LE is a powerful, user-friendly hedge trimmer that combines efficiency with comfort. Its advanced engine technology, sharp dual blades, and ergonomic design make it a dependable choice for those looking to maintain their outdoor spaces. Whether tackling overgrown hedges or shaping ornamental shrubs, the BH2160 LE offers reliability and power suitable for a variety of gardening tasks.
Top Page Image Contents