Poulan BH2160 LE instruction manual Checking the tension, Chain Tension, Adjusting the tension

Page 7

Cutters

Depth Gauge

Checking the tension:

 

 

Use the screwdriver end of the chain adjust-

 

 

ment tool (bar tool) to move the chain around

 

 

the bar. If the chain does not rotate, it is too

 

 

tight. If too loose, the chain will sag below the

 

 

bar.

Drive Links

Place chain onto the sprocket

7.Place chain over and behind clutch, fit- ting the drive links in the clutch drum sprocket.

8.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

9.Fit chain drive links into bar groove.

10.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

NOTE: CHAIN BRAKE MUST BE DISENGAGED BEFORE INSTALLA- TION ON THE SAW. TO DISENGAGE CHAIN BRAKE, PULL THE FRONT HAND GUARD BACK TOWARD THE REAR OF THE CHAIN BRAKE AS FAR AS POSSIBLE (SEE ILLUSTRA- TION).

DISENGAGED

Front Hand Guard

ENGAGED

Chain Brake

11.Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar. Remember this pin moves the bar forward and backward as the screw is turned.

12.Install chain brake nuts and finger tight- en only. Once the chain is tensioned, you will need to tighten chain brake nuts.

CHAIN TENSION

(Including units with chain already installed) NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage.

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

You can adjust the chain tension by loosen- ing the chain brake nuts and turning the ad- justing screw 1/4 of a turn while lifting up on the bar.

SIf chain is too tight, turn adjusting screw 1/4 turn counterclockwise.

SIf chain is too loose, turn adjusting screw 1/4 turn clockwise.

Adjusting

Screw

Chain Brake Nuts

Guide Bar

Adjusting Screw -- 1/4 Turn

S Lift up the tip of the bar and tighten the chain brake nuts with the bar tool.

SRecheck chain tension.

Chain Brake

Nuts

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 16/04 English Español FrançaisSafety Rules Identification of SymbolsPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control 952044370 Chain Brake and CKA AngleFront Hand Guard, designed to reduce Back toward the operatorChain Brake Nuts AssemblyInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notChecking the tension Adjusting the tensionChain Tension Throttle LOCK-OUT ON/STOP SwitchKnow Your Chain SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationStarting a Warm Engine Cutting MethodsImportant Points Direction of Fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeBucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingPruning ServiceLimbing and Pruning Important Points LimbingInspect Muffler and Spark Arresting Screen Cleaning the air filterCleaning the Spark ARREST- ING Screen AIR FilterIgnition Timing Carburetor AdjustmentBAR Maintenance Chain SharpeningNeed ASSISTANCE? Need Service PART?Need ASSISTANCE? StorageTions The U.S. Environmental Protection Limited WarrantyPlacement and Repair of Emission

BH2160 LE specifications

The Poulan BH2160 LE is a versatile and robust hedge trimmer designed for homeowners and landscaping professionals alike. As part of Poulan’s esteemed line of outdoor power equipment, the BH2160 LE delivers outstanding cutting performance, making it an essential tool for maintaining your garden and yard.

One of the standout features of the BH2160 LE is its powerful 24cc, 2-cycle engine. This engine offers an impressive balance of power and efficiency, enabling users to tackle thick and dense hedges with ease. The lightweight design of the trimmer, combined with its ergonomic handle, ensures comfort during extended use, reducing fatigue and allowing for precise maneuverability.

The BH2160 LE is equipped with a 22-inch dual reciprocating blade, designed for efficient and smooth cutting. The sharpened cutting edges of the blades provide a clean cut, promoting healthy growth in hedges and shrubs. One notable technology incorporated into the design is the anti-vibration system, which minimizes vibrations transmitted to the operator, thus enhancing comfort during operation.

Another key characteristic of the Poulan BH2160 LE is its availability with an adjustable handle. This feature allows users to customize their grip position according to their personal preference and the nature of the task at hand. Additionally, the trimmer’s built-in blade guard adds an extra layer of safety, protecting both the user and the blades from damage during storage and transportation.

For ease of use and maintenance, the BH2160 LE comes with a tool-less air filter access feature. This innovation simplifies filter cleaning and replacement, extending the lifespan of the engine and ensuring optimal performance. Moreover, the model features a fuel tank designed for easy refueling and minimizes the risk of spills.

Overall, the Poulan BH2160 LE is a powerful, user-friendly hedge trimmer that combines efficiency with comfort. Its advanced engine technology, sharp dual blades, and ergonomic design make it a dependable choice for those looking to maintain their outdoor spaces. Whether tackling overgrown hedges or shaping ornamental shrubs, the BH2160 LE offers reliability and power suitable for a variety of gardening tasks.
Top Page Image Contents